Explain what criteria are used in the selection of personnel

Assignment Help Civil Engineering
Reference no: EM13143034

Civil and Environmental Engineering
1 What is the purpose of maintainability prediction? When are maintainability predictions accomplished in the life cycle?

2 How are preventive maintenance requirements determined? How are they justified? What is likely to occur if they are not properly justified?

3 What criteria are used in the selection of personnel for the demonstration of maintenance tasks? Define the criteria for the selection of test and support equipment.

4 Define what is meant by human factors. When in the system life cycle are human factors considered? Why is it important to consider human factors in design?

5 What effects on the human are likely to occur if the operator in performing his or her funtion is undertrained for the job? Overtrained? How would these effects likely influence system operation?

6 What are the possible uses and benefits of a mockup?

7 What factors should be considered in determining supply support requirements? Test and support equipment requirements? Personnel requirements? training requirements? Transportation and handling requirements? Facility requirements? Technical Data requirements?

8 How can Packaging design impact the reliability of a system (if at all)?

9 Describe total productive maintenance (TPM). What are the objectives of TPM?Metrics? How does it relate to ILS (if at all)?

10 Define producibility. Why is it important? When in the system life cycle should it be addressed?

11 Define Disposability. Why is it important? When in the system life cycleshould it be addressed? How does it relate to productibility?

12 What is meant by demanufacture? Provide some examples.

Reference no: EM13143034

Questions Cloud

Find probability that the entire batch will be rejected : The entire batch will be rejected if at least one of those tested is defective. What is the probability that the entire batch will be rejected? Assume independence.
What is the due date of note : sunhine service center received a 120-day, 6% note for $40,000, dated April 12 from a customer on account. What is the due date of the note?
How many distinct molecular mechanisms might be responsible : How many distinct molecular mechanisms might be responsible for converting a proto-oncogene into a potent oncogene? What are they and how might they be responsible for the converting?
Determine the total number of moles of oxygen : given the balanced equation representing a reacction: 2C2H6+7O2=4CO2+6H2O determine the total number of moles of oxygen that react completely with 8.0 moles of C2H6
Explain what criteria are used in the selection of personnel : What criteria are used in the selection of personnel for the demonstration of maintenance tasks? Define the criteria for the selection of test and support equipment.
The challenges facing the united states labor unions : "Analytical Analysis Questions and Genres"Please respond to the following: Select a topic from the ones provided here and identify three questions that you want to have answered through your research.
Can enhancers work in trans : Can enhancers work in trans? That is, can an enhancer on one piece of DNA activate a promoter on another piece of DNA. Propose an experiment to test this. Be sure to discuss any appropriate control experiments.
How many moles of atoms are present : How many moles of atoms are in each of the following? 4.1*10^24 Pb atoms ,2.15*10^22 He atoms
Reallocating expenditures between the goods : At present she is buying these products in amounts such that the marginal utilites from the last units purchased of the two products are 80 and 70 units, respectively. Is she buying the utility-maximizing combination of bread & milk? How should sh..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Average waiting time in the queue

What is the average length of queue, the average time spent in the system, and the average waiting time in the queue?

  Strength of a semicrystalline polymer

Briefly explain how each of the following influences the tensile or yield strength of a semicrystalline polymer and why: (a) Molecular weight (b) Degree of crystallinity (c) Deformation by drawing (d) Annealing of an undeformed material

  Estimate the particle removal efficiency

How do you propose to do this at the above treatment plant and estimate the head loss both immediately after backwash and 10 hours later, if the same water is applied at a rate of 2 L/s.m 2 .

  What is the new water content

A soil sample with a water content of 14.5% and unit weight of 128.2 lb/cu. ft. was dried to a unit weight of 118.8 lb/cu. ft. without changing its void ratio. What is its new water content (in %)?

  Standard test method for flash and fire points

What is the procedure standard test method for flash and fire points by cleveland open cup tester if there is animation or video is better....

  Find out the magnitude of the contraction scour

Bridge scour, Determine the magnitude of the contraction scour depth given the following information about the channel and bridge

  Pressure on the soil if theta is given

A pipe is to be installed under the ground on a bed of aggregate 6 in. thick. The entire weight on the aggregate from pipe and soil above the pipe is 1800 lbs. per linear foot of pipe. What is the pressure on the soil if theta is 45 degrees? Assum..

  Draw the influence line for the support reaction

Draw the influence line for the support reaction at A and calculate the support reaction at point

  Determine the volume flow rate of water

Water with a static pressure of 1.96kN/M 2 flows through an 800 mm diameter pipe. A pitot tube pressure gage in this pipe reads a pressure of 5.88 kN/M 2 . How do you determine the volume flow rate (Q) of the water? (Q = 1.40 M^3/sec, V=2.79 M/se..

  Unit of measurement and unit of payment

Write the unit of measurement and unit of payment of following items. 1) Earthwork in excavation in foundation. 2) Framwork. 3) Steelwork in trusses. 4) Damp proof course D.P.C. 5) Cement.

  Tightening of bolt in the friction grip

What difference does the tightening of bolt in the friction grip joint make to the load at first slip and the failure load.

  Maximum acceptable tensile service load

Compute the maximum acceptable tensile service load T that may act on a single angle L6x4x3/4 that is welded along only one leg to a gusset plate; thus, there are no holes. The service load is three times the dead load. Solve for a0 A36 steel.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd