Explain two steel plates are joined with a butt weld

Assignment Help Mechanical Engineering
Reference no: EM13137636

Weld analysis
Two steel plates are joined with a butt weld using a weld throat h of 3/8 in. and the length of weld 1 of 4in. How do I determine the shear stress in the weld for a shearing force of 15000 lbf?

Reference no: EM13137636

Questions Cloud

Compute the simple interest rate required : Assume you have $3,000 in your bank account today and you decide to transfer the money into a special educational deposit, which has been newly introduced by the bank.
Explain midrange and amplitude components : Midrange and amplitude components, A shaft is subjected to a completely reversed bending stress such that Xmax=40kpsi and Xmin=-40kpsi
What are several individual recommendations : What are several individual recommendations for Whites/European Americans within a work environment?
State that the average weekly salary for all teachers : With what degree of confidance can we state that the average weekly salary for all teachers in this area is between $487 and /4517.
Explain two steel plates are joined with a butt weld : Weld analysis, Two steel plates are joined with a butt weld using a weld throat h of 3/8 in. and the length of weld 1 of 4in.
What is the profit-maximizing : What is the profit-maximizing P in the case that Godzilla and Macrosoft merge
Calculate the mass percent of caco3 in the original mixture : A mixture of CaCO3 and CaO weighing 0.630 g was heated to produce gaseous CO2. After heating, the remaining solid weighed 0.500 g.
What would be the amount of differential cost increase : Sparrow Co. is currently operating at 80% of capacity and is currently purchasing a part used in its manufacturing operations for $8.00 a unit. The unit cost for Sparrow Co.
Goals and objectives of terrorists : This answer is a discussion of how terrorists from every tradition are often motivated by a political theology that fuses moral, religious, and political goals and seeks the reformation of society.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Computation of percentage heat reduction

Calculation of percentage heat reduction, Water at 90 C flows through a 50mm bore steel pipe of wall thickness 8 mm. Ambient temperature is 18 C. Calculate the heat loss per metre length of pipe

  Alternative methods for casting the concrete for the wall

Compare the time and cost of using the following three alternative methods for casting the concrete for the wall: 1) direct chute 2) pumped 3) crane and bucket.

  Explain fluid statics- submerged submarine

Fluid Statics: Submerged Submarine, A submarine is at a depth of 2000 ft from the water surface. The atmospheric pressure above the water is at 14.7 psia

  Explain the compression ratio of an air-standard otto cycle

The compression ratio of an air-standard Otto cycle is 9.5. Prior to the isentropic compression process, the air is at 100 kPa, 17 C, and 600 cm2

  Newtons law to find the tension in the string

draw a free body diagram for each of the two situations. use the "radial" Newton's law to find the tension in the string at each of these situations.

  Determine the maximum shear stress

Draw the Mohr's circle for this stress state, deterrnine the principal stresses and the angle of the principal direction to the x-axis and determine the maximum shear stress.

  Evaluate the exit velocity

Evaluate the valve closure to achieve a water exit velocity

  Draw the block diagram of the uncontrolled seat

Draw the block diagram of the uncontrolled seat Plot the open loop displacement response of the uncontrolled seat to a step input

  Explain compressive stress

Important information about Compressive Stress, A circular cross sectional bar with a diameter of 3.25 inches is loaded with a uniform axial compressive load of 22,750 pounds. What is the compressive stress along a cross section of the bar?

  Meaning of the term mechatronics

Briefly describe the meaning of the term mechatronics both in terms of the 'systems approach' and the technology involved.

  What could be some of the strategies

How may data be managed to support a function (billing, human resources, accounting, finance, sales/marketing, training)?

  Explain a car and a high speed trian at constant speeds

A car and a high -speed trian at constant speeds. three seconds after the train passes under the highway bridge the car crosses the bridge.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd