Explain the true altitude of the plane above sea level

Assignment Help Mechanical Engineering
Reference no: EM13137399

Altimeter reading

An aeroplane is fitted with an altimeter calibrated assuming the atmosphere meets the ISA specification. On a day when sea level pressure and temperature are 101,500 N/m2 and 25 degrees the altimeter reads 5000m. What is the true altitude of the plane above sea level? What would be the indicated altitude after landing at an aerodrome located at sea level? (Gas const = R=288 J/KgK)

Ans = 5186m, 16.6m below sea level)

Reference no: EM13137399

Questions Cloud

Which basis of allocating the cost is most likely : If the cost of ZZ is allocated to the X and Y products on the basis of the number of gallons produced, how much of the total cost of the 400 drums should be charged to each product?
Explain how a monopolist can increase profits : What is the main difference between the demand curves for the perfect competitor and the monopolist?  Explain the difference between the firm's demand curve for each and then for the market for each.
Explain horsepower and efficiency of three-phase motor : Horsepower and efficiency of three-phase motor, If a fully loaded 440V, three-phase motor draws 12.4 A at 86% power factor (pf). It's speed is 1730 rpm and its torque output to a mechanical load is 29.1 lb-ft x 1.356 = 39.5 Nm.
Identify population and sample for humidity set : The amount of food consumed by each rat with humidity set at 20% and again with humidity set at 60%. For this study, identify (a)the population and (b) the sample.
Explain the true altitude of the plane above sea level : What is the true altitude of the plane above sea level? What would be the indicated altitude after landing at an aerodrome located at sea level? (Gas const = R=288 J/KgK)
Written report and oral report : .Tell us under what circumstances you prefer to use a written report and when you prefer to give an oral report. What are the advantages and disadvantages of each?
Define advantages and disadvantages of the us gaap : What are the advantages and disadvantages of the US GAAP bright line approach versus the IFRS conceptual approach in determining the classification of a lease?
Theory of commercial impracticability : May return the computers and avoid paying for them because the contract was void under the theory of commercial impracticability.
How does this compare to the overhead cost charged : Assume that in the current year, the company continues to allocate overhead based on labor hours. What would be the overhead cost of an 8-labor-hour job requested by Jasmine’s Fine Jewelry? How does this compare to the overhead cost charged to suc..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Determine heat flow heat flow through a uniform wall

Determine heat flow, Heat flow through a uniform wall will: a) increase as the thermal resistance increases b) increase as the thickness of the wall increases

  Steady state thermal analysis

Steady State Thermal analysis can be use to simulate and obtain results to support the design optimization / objectives

  Automatic control

DOF system and Find the differential equation describing the system

  Brick cube is then placed in ambient temperature conditions

A fireclay brick cube, 10 cm in length is removed from a furnace where it was maintained at a temperature of 500 degrees C. The brick cube is then placed in ambient temperature conditions.

  What is discharge revised discharge pressure of compressor

What is the discharge revised discharge pressure (guage pressure) of the compressor ?  Is the assumption of change in temperature valid for calculating the discharge pressure of the compressor ?

  Hydrostatic relation an empirical formula relating

Hydrostatic relation, An empirical formula relating pressure and density for seawater w/ temperature held constant is

  Explain piston-cylinder assembly undergoes a constant

Refrigerant R-134a vapor in a piston-cylinder assembly undergoes a constant-pressure process from saturated vapor at 800 kPa to 50 ºC.

  Solve for the dynamics of the resulting system

Solve for the dynamics of the resulting system for 20 seconds of real time using midpoint method.

  Drilling fluid engineering manual

Read the titled books Drilling Fluid Engineering Manual. Textbook prepared by M-I Drilling Fluids Co.,1998; Halliburton Cementing Tables. Casing and cement data tables prepared by Halliburton Company.

  Define centrifugal clutch

Centrifugal Clutch Question, In a centrifugal clutch there are eight shoes, each of mass 0.3 kg and the centre of gravity of each shoe is at 50 mm radius when it is just touching the drum of diameter 200 mm.

  Temperature and density of air for an adiabatic process

Effect of pressure on temperature and density of air for an adiabatic process, The pressure is to be raised from atmospheric to 7 psi (4.83 bar). The process is adiabatic, and the volume is constant and unknown.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd