Explain the steam from the nozzles of a single wheel impulse

Assignment Help Mechanical Engineering
Reference no: EM13137731

The steam from the nozzles of a single wheel impulse turbine discharges with a velocity of 600 m/s at an angle of 20 degrees. The blade wheel rotates at 3000 rev/min and the mean blade radius is 590 mm. The axial velocity of the stream at the exit from the blades is 164 m/s and the blades are symmetrical.

Sketch the annotated velocity triangles and calculate:
a) the blade inlet angle
b) the diagram specific work
c) the diagram efficiency
d) the blade velocity coefficient
e) Show that for symmetrical blading and no friction n_rot = 4(U/V_1)(cos(alpha_1) - (U/V_1)) and determine the optimum blade speed ratio and efficiency. Make a sketch of your results.

Reference no: EM13137731

Questions Cloud

How to show that your method of calculation is accurate : if you have 20 journal entries for the past 6 months that need to be re-calculated to reflect a 20% commission payout on 15 employee's what method would you use to show that your method of calculation is accurate?
What is the employer payroll tax expense : Social security tax rate, 6% on maximum of $100,000; and Medicare tax rate, 1.5% on all earnings; state unemployment compensation tax, 3.4% on the first $7,000; federal unemployment compensation tax, .8% on the first $7,000. What is the employer's..
Women and the minorities in politics : What influence have women had on the politics in local, state and national government? What influence have other minorities had on the political landscape in local, state and national politics?
What percent of babies born in gestation period-low weight : During the gestation period of 28 weeks, what percent of the babies born within each gestation period have a low birth weight (under 5.5 lbs)?
Explain the steam from the nozzles of a single wheel impulse : The steam from the nozzles of a single wheel impulse turbine discharges with a velocity of 600 m/s at an angle of 20 degrees. The blade wheel rotates at 3000 rev/min and the mean blade radius is 590 mm
Government role on private lives : What role should local government have on the lives of its citizens? How much control or influence should local government have in the lives of its citizens?
Paper on entrepreneurship and what it has to do with leader : 7-10 page paper on entrepreneurship and what it has to do with leadership
How many ml of the drug should the patient receive : A patient weighs 146 pounds and is to receive a drug at a dosage of 45.0 mg per kg of body weight. The drug is supplied as a solution that contains 25.0 mg of drug per mL of solution.
What is randolph basis in the distributed inventory : Randolph's basis in RD is $37,000. What is Randolph's basis in the distributed inventory and land?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd