Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Light-Voice Controlling System.We are planning to design a new light-voice controlling system. The voices will basically coordinate the crossing of a road by blind people. Suppose the crossing will be operated by two coordinated systems: a light system and a voice system. The light controlling system is an ordinary set of traffic lights intended for vehicles, but with the amber light flashing before the lights change over to green. These lights operate in cycles and display the colors in the order: green, continuous amber, red, flashing amber, green. The set of voices is intended for blind people and makes alternately the voices 'You can cross' and 'Stop'. Making the voice 'You can cross' goes through two phases; a first voice phase 'You can cross' followed by a second voice phase 'Prepare to stop' before the sound change to the 'Stop' voice. The voice 'Stop' lasts through exactly the period from the onset of the green light in traffic lights to the end of the continuous display of the amber light. The periods of playing the voice 'You can cross' and the amber traffic light are also the same. No two lights or two voices are to be displayed or played together at any time in either set when taken in isolation. To simplify the design, we will assume the crossing is not controlled by blind people and that the lights are operated continuously in approximately fixed cycles. Timing parameters of the display of lights or playing of voices are as follows.Phase Delay of phaseGreen light d1Red light d2Continuous amber light d3Flashing amber light d4Voice 'You can cross' d5Voice 'Prepare to stop' d6Voice 'Stop' d7
1) (5 points) Identify all the components of this new crossing system
2) (15 points) Give a global state transition diagram for this system
For satisfactory operation, the static pressure at the pump inlet must not be lower than -6 m of water gage. Determine the smallest standard commercial pipe that will give the required performance.
Compute the maximum acceptable service load on an A36 steel plate tension member 1/4in.x12in. having a single line of holes parallel to the direction of loading. The load is 25% dead load and 75% live load, and 7/8in. diameter bolts are used.
Roman technology and engineering. Technology and engineering were among Rome's most famous achievements. Describe and explain the importance of Roman technology and engineering
Water flows through a horizotal 45 deg reducing bend with a 36 inch. diameter upstream and a 24 inch diameter downstream, at the rate of 20 cfs under a pressure of 15 psi at the upstream end of the bend. Neglecting head loss in the bend, calculate..
If the queue clears exactly at the end of the effective green D/D/1 queuing applies, determine the total vehicle delay in the cycle (in veh-sec) .
The height (in meters) of a projectile shot vertically upward from a point 2 m above ground level with an initial velocity of 24.5 m/s is h2+24.5t-4.9t^2 after t seconds. a) When does the projectile reach its maximum height? b) What is the maximum..
What is the average length of queue, the average time spent in the system, and the average waiting time in the queue?
A rectangular channel 2.0 m wide carrying a discharge of 2.5 m3/s is to be fitted with a weir at its downstream end to provide a means of flow measurement as well as to cause heading-up of the water surface.
What is the Federal Express philosophy toward quality? What specific elements/actions has FedEx implemented in its quality improvement history?
How many gallons of mercury (sg=13.54) would weight the same as 5 gallons of castor oil which has a specific weight of 56.69 pcf?
Compute the maximum acceptable tensile service load T that may act on a single angle L6x4x3/4 that is welded along only one leg to a gusset plate; thus, there are no holes. The service load is three times the dead load. Solve for a0 A36 steel.
A conical tube of length 8 m fixed vertically with its smaller end upwards. The velocity head and pressure head at upper ends are 1.27 m and 2.50 m respectively.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd