Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Let's assume that system is characterized by the following input/output equation: y(t)=1000· x(t-200) where t is given in msec and x(t) in mV.
What time delay in msec would you expect to find the signal relatively to real time?
What range of values in units of Volts would you expect y(t) to have if we assume that the range of x(t) is ±1mV? What are the units of the gain 1000 of the amplifier?
Is the system an LTI system? Explain (Prove)
Find and sketch y(t) when x(t) is a train of action potentials (model the action potentials as δ-impulses) 100 msec apart from each other. Justify your drawing on the basis of your answer in (c) above and related properties of LTI systems and δ(t). [hint: find h(t)]
If a frame is damaged then in this network the receiver sends back a request for retransmission. (For simplicity, assume all these requests arrive back perfectly at the sender). What is the mean number of transmissions required to successfully tra..
The switch in the circuit has been in position a for a long time. At t=0 the switch is moved to position b. A.Calculate the initial voltage on the capacitor ifv = 200V , and i = 1.9mA . B. Calculate the final voltage on the capacitor. C. Calculate t..
A device moves 120 coulombs of charge from point a to b in 8 seconds. the distance between a and b is 6 cm. the energy expended in moving the charge is 600 Ws. calculate the voltage between a and b.
An amplifier provides 10.5 V output under unloaded condition. When a load of 10-ohm is connected at its output, the voltage drops down to 0.5 V. Find out the output resistance of the buffer that is to be put between the amplifier
Suppose q1 = 10. nC is located at the Cartesian coordinate point (4.0 m, 0.0 m, 0.0 m). A second charge q2 (-4.0 m, 0.0 m, 0.0 m) = -10. nC. If a test charge qt(0.0 m, 0.0 m, 3.0 m) = 0.10 nC
Design a non-inverting amplifier with a voltage gain of approximately 12 with an input resistance of 12kOhm. Use SPICE to confirm the result using a simple model of the OpAmp
Design an adder that computes the sum of four 8-bit numbers, using 8-bit carryripple adders. Use a basic 8-bit carry-ripple adder as a building block for the design.
find values of resistance, voltage, and current for total and all 3 voltage drops where only certain information is given out of three voltage drops info given total voltage is 12v, resistance 1 is 2.2KO, resistance 2 is 1.6KO, and resistance 3 is..
(1) If you have a transformer that is not in a circuit, how can you tell/determine what the ratio is (2) How do you tell if a diode is forward or bias. How much voltage is assumed dropped across a forward biased silicon diode. Reversed biased sili..
A discrete-time LTI system has the impulse response h[n]. Use linearity and time invariance to determine the system output y[n] if the input is h[n]={-2:n=-1, 3:n=0, 2:n=3, -4:n=5}
construct a simple SR latch using push-buttons for inputs and l.e.d.s for outputs. Describe the timing of output changes with reference to input changes. ON THE SAME PAGE, construct a simple clocked D-type clocked flip-flop, again using a push but..
Bipolar Junction Transistor, A silicon n-p-n bipolar junction transistor is designed with emitter, base and collector doping levels of 10^19cm, 10^15cm and 5*10^17cm, respectively.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd