Exit temp of the air and the rate of heat transfer from air

Assignment Help Mechanical Engineering
Reference no: EM13710417

Air enters the evaporator of an air conditioner at 14.7 psia, 90F, 200 ft3/min. R-134a at 20 psia, 30%  quality enters at 4 lbm/min and leaves as saturated vapor at the same pressure. Find the exit temp of the air and the rate of heat transfer from the air.

Reference no: EM13710417

Questions Cloud

Biogas becomes flammable if the oxygen content exceeds : 100 kmol/h of biogas (75 mol% CH4 and 25 mol% CO2) is produced in a digester and is drawn off from the headspace under a slight vacuum and piped to a natural gas burning boiler. A slight leak develops in the pipe allowing air (79 mol% N2 and 21 mol% ..
Estimate how fast the baseball is moving : A 0.15 kg baseball collides with a 1.1 kg bat. The ball has a velocity of 43.5 m/s immediately before the collision. Estimate how fast the baseball is moving
What is the steady state surface temperature : A cylindrical electric resistance heater has a diameter of 1cm and length of 0.25m. When water at 30oC flows across the heater a heat-transfer coefficient of 15W/(m2oC) exists at the surface. If the electrical input to the heater is 5W, what is the s..
Determine the initial velocity of the mass : A 0.25 kg mass on a spring has a displacement x(t) = 0.2 cos(1.2 t - 0.15?). Determine the initial velocity of the mass
Exit temp of the air and the rate of heat transfer from air : Air enters the evaporator of an air conditioner at 14.7 psia, 90F, 200 ft3/min. R-134a at 20 psia, 30%  quality enters at 4 lbm/min and leaves as saturated vapor at the same pressure. Find the exit temp of the air and the rate of heat transfer from t..
Changes in kinetic and potential energies are zero : Water in a vertical piston cylinder is heated at constant pressure of 10 bar. It is initially at 179.9 0C and has a specific volume of 0.1 m3/kg and is heated to a final specific volume of 0.248 m3/kg. Changes in kinetic and potential energies are ze..
What is the angular frequency of this oscillator : A block of mass m= .6 kg is attached to a spring with a natural frequency of oscillation f= 1.45 Hz. What is the angular frequency of this oscillator
What should his speed have been at the top of the ramp : A physics professor did daredevil stunts in his spare time. His last stunt was an attempt to jump across a river on a motorcycle. What should his speed have been at the top of the ramp
Frictionless slot that lies in the vertical plane : The 8-lb block slides in a frictionless slot that lies in the vertical plane. The stiffness’s of springs A and B attached to the block are kA =40 lb/ft and kB= 20 lb/ft. When the block is in position 1, spring A is compressed 0.5 ft and spring B is u..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd