Exceptional thermal-insulation properties

Assignment Help Mechanical Engineering
Reference no: EM13709590

The thermal protection system for NASA's Space Shuttle Orbiter was effective due to its exceptional thermal-insulation properties. Calculate the heat flow (per square meter) across a 50-mm-thick ceramic tile with an outer surface temperature of 1200 degrees C and an inner surface temperature of 30 degrees C, given a thermal conductivity of 0.0837 J/(s x m x K).

Reference no: EM13709590

Questions Cloud

Masses connected together with a mass less rigid-link : Given three masses connected together with a mass less rigid-link, where should you place the single mass if you want to replace these masses with it?
Steam enters diffuser operating steady state with pressure : Steam enters a diffuser operating at steady state with a pressure of 14.7 psi, a temperature of 300F, and a velocity of 500ft/s. Steam exits the diffuser as a saturated vapor with negligible kinetic energy. Heat transfer occurs from the steam to its ..
Determine the exit velocity of the nitrogen : Nitrogen gas at 65kPa and 7C enters an adiabatic diffuser steadily with a velocity of 210 m/s and leaves at 119kPa and 22C. Determine  the exit velocity of the nitrogen. the ratio of the inlet to exit area
What must be the surface area of the lift cylinder : A hydraulic lift must lift 7000 lbs using oil that is under pressure of 130 lbs/in^2. what must be the surface area of the lift cylinder?
Exceptional thermal-insulation properties : The thermal protection system for NASA's Space Shuttle Orbiter was effective due to its exceptional thermal-insulation properties. Calculate the heat flow (per square meter) across a 50-mm-thick ceramic tile with an outer surface temperature of 1200 ..
The amount of heat transfer during the whole process : 1.5 kg of air in a piston/cylinder assembly has initial temperature and pressure 27oC and 1.5 bar respectively. Then the system is heated in constant volume to 727oC (state 1-2) and then heated again constant pressure to 1227oC (state 2-3).Determine ..
Maximum tensile and compressive stress acting on the beam : If the built-up beam is subjected to an internal moment of 75 kn*m, determine the maximum tensile and compressive stress acting on the beam
Volcano has erupted-spewing stones-steam : A volcano has erupted, spewing stones, steam, and ash several thousand feet into the atmosphere. After some time, the particles begin to settle to the ground. Consider a nearly spherical ash particle that is 50 microns in diameter, falling in air who..
The standard atmosphere at sea level : Find the terminal velocity of an 8.5-inch-diameter sphere weighing 16 lbf falling through the following fluids under the action of gravity: (a) the standard atmosphere at sea level; (b) the standard atmosphere at 10,000 ft elevation above MSL; (c) wa..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the velocity of the water at the inlet and exit

A pump is employed to deliver liquid water from a pond to a higher elevation. The pump steadily draws water from the pond at a volumetric flow rate of 192 gal/min through a pipe having a 7 in diameter inlet. The exit diameter of the pipe is 2 in. and..

  Determine heat flow heat flow through a uniform wall

Determine heat flow, Heat flow through a uniform wall will: a) increase as the thermal resistance increases b) increase as the thickness of the wall increases

  How thick does the 4140 steel need to be if it is a

how thick does the 4140 steel need to be if it is a cyclander with a diameter of 8.252 inches and is 1.5 inches deep

  Define and design a hollow steel shaft to transmit

Hollow shaft transmitting power with shear limits. Design a hollow steel shaft to transmit 300 hp at 75 rpm without exceeding a shear tress of 8000 psi. Use 1.2:1 as the ratio of the outside diameter to the inside diameter.

  What is the energy of vacancy formation in this element

The equilibrium number of vacancies for an element is 3.100 x 10-6 at 600°C and 5.880 x 10-6 at 1300°C. What is the energy of vacancy formation in this element?

  Determine the final pressure temperature and specific

two well-insulated and rigid vessels are interconnected by a pipe and a valve. one 85 liter vessel contains oxygen at

  What is the magnitude of the angular momentumthe current

voyager 1 is on an escape trajectory from the solar system with the orbital element a - 480926000 km e 3.724716a what

  Determine how much force will be required to stretch them

a set of steel reinforcing rods is to be stretched axially in tension to create a tensile stress of 30ksi prior to

  Evaluate the work required and the heat transfer

Kinetic and potential energy effects can be ignored. Evaluate the work required and the heat transfer, each in kW.

  Vector a has components ax 124 ay 221 vector b has

vector a has components ax 1.24 ay 2.21 vector b has components bx 4.06 b-y -3.66. find the counterclockwise angle

  If the dew point is 10 oc determine the thickness of the

in a pharmaceutical plant a copper pipe kc 400 wm.k with inner diameter of 20 mm and wall thickness of 2.5 mm is used

  A valve in the line connecting the two tanks is opened and

two well-insulated tanks contain air. initially tank a hold 1.0 lb of air at 1440 r and tank b has 2.0 lb of air at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd