Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Evaluate the component selection for the differentiator and integrator amplifiers and their impact on the mahematical equation for each. Items for you to consider and discuss are:
Do you observe any limitation factors for the component parameters and the input signal frequencies?
Comment on the influence of the amplifier's input impedance?
For high frequencies, what effects are observed for each amplifier? Will the op amp parameters influence the circuit operation?
For low frequencies, what effects are observed for each amplifier? Will the op amp parameters influence the circuit operation?
An LVDT (Linear Variable Differential Transformer) is used in an accelerometer to measure seismic-mass displacement. The LVDT and signal-conditioning output is 0.31 mV/mm with a +/- 2 cm maximum core displacement.
In comparing the behaviour of an n-channel MOSFET with a p-channel device having identical geometry and threshold voltage, it is found that the n-channel FET has a greater drain current than that of the p-channel FET.
A series circuit has a 1k(ohm) resistance and a 1k(ohm) inductive reactance. v1= 1 vrms a. what is the impedance of the circuit in rectangular form b. the frequency is given as 1kHz, what is the inductance of the coil L= c.
Compute and plot the correlation sequences r s1s2 (l), r s0s0 (l), r s1s0 (l) and r s2s0 (l) . Compute and plot the cross-correlation sequences and of the received signal with the template signals and s 2 (n).
A recording trace r(t) is definedas r(t) = s(t) + n(t), where s(t) =10sin(20?t) (i.e., a 10 Hz sine wave, given f= 2f) is the signal and n(t) = sin(120t) (i.e., the 60 Hz electromagnetic noise) the noise.
Sketch the theoretical torque vs. speed characteristics for a series, shunt, and compound connected DC motor. Describe what will happen if a series motor is run under no load conditions. describe what will happen if a shunt motor experiences a lo..
A PWM is to be programmed to output a signal with a pulse high width of 150 usec and a pulse low width of 250 usec. What are the values required for prescale (if any) PWMPER and PWMDTY An 8-bit configuration is used and the E-clock is 24 MHz.
Suppose that without a 1k-ohm load an amplifier's output voltage is 5Vpp but when the 1k-ohm load is attached, it drops to 3Vpp. What is the output impedance of the amplifier
A composite analog signal is given in the following expression: x(t)=1.2 sin(2pi60ft)+0.0001cos(2pi1ft) -If this signal was sampled at 1000 Hz, derive the expression for the sampled sequence x[n] with n being the sampling index.
Pulse Generator, Using one 555 timer, design a pulse generator that will have the following continuously variable ranges
1) For a forwarard converter, derive the minimum value of Vr - as a function of the input voltage Vg, the duty cycle D, and the turns ratio N1/N2 - that will cause the transformer magnetizing current to be reset to zero by the end of the switching..
The z-transform X(z) of a causal sequence x[n] has a zero at z1 = 0 and three poles at p1 = 3/4 and p2,3 = (1/2)(1 ± j). Determine the z-transform Y(z) of the sequence y[n] = x[n + 3], its pole-zero pattern, and its ROC.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd