Ethanol c2h5oh is burned with air in a sie with a fuel-rich

Assignment Help Mechanical Engineering
Reference no: EM13620488

Ethanol (C2H5OH) is burned with air in a SIE with a fuel-rich mixture. Consider MON = 89 and RON = 107 for this fuel. Consider the molecular weight of the following substances are; C:12, O:16, H:1, N:14 kg/kmol

Determine:

(i) Equivalence ratio.

(ii) Anti-knock index (AKI) and fuel sensitivity (FS) of this fuel.

Reference no: EM13620488

Questions Cloud

Two lb of water vapor in a piston cylinder assembly is : two lb of water vapor in a piston cylinder assembly is compressed at a constant pressure of of 250 lbfin2 from a volume
A carnot engine whose low-temperature reservoir is at : a carnot engine whose low-temperature reservoir is at 19.7degc has an efficiency of 26.8. by how much should the
Barna research group collected data showing church : barna research group collected data showing church attendance by age group usa today november 20 2003. use the sample
What changes have occurred in the human service sector : what changes have occurred in the human service sector that have made government and private contributors more
Ethanol c2h5oh is burned with air in a sie with a fuel-rich : ethanol c2h5oh is burned with air in a sie with a fuel-rich mixture. consider mon 89 and ron 107 for this fuel.
Mind blowers inc has a new project in mind that will : mind blowers inc. has a new project in mind that will increase accounts receivable by 28000 decrease accounts payable
You are analyzing a project and have developed the : you are analyzing a project and have developed the following estimates unit sales 1320 price per unit 79 variable
Evaluate the thermal conductivity of copper and constantan : the temperature of a flowing gas is to be measured with a thermocouple junction and wire stretched between two legs of
A project has sales of 462000 costs of 274000 depreciation : a project has sales of 462000 costs of 274000 depreciation of 26000 interest expense of 3400 and a tax rate of 35

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Using variable specific heat method

1. A Brayton cycle uses air and produces a net work of 14000 Btu/s with an inlet state of 60°F, 14.7 psi and a compression ratio of 16. The heat added in the combustion process is 400 Btu/lbm. If the thermal efficiency is 0.547 Determine: Using va..

  The pressure in a partially evacuated enclosure is 268 in

the pressure in a partially evacuated enclosure is 26.8 in hg vacuum when the local barometer reads 29.5 in hg.

  Calculate the pressure of air inside the cylinder before

a well-insulated vertical piston-cylinder device contains air. the diameter of the piston is 8 inches. atmospheric

  The speed of water at the beginning of the pipe is 150 fts

water flows into an 9.0 diameter section of a piping system then it exits from 3.0 x 4.0 rectangular section. the speed

  The aim of this demonstration is to use measurements of the

the aim of this demonstration is to use measurements of the load required to propagate a crack tear in packaging tape

  Cooling water enters the tubes at 15degc 1bar and exits at

steam at a pressure of 0.08 bar and a quality of 93.2 enters a shell-and-tube heat exchanger where it condenses on the

  Determine the natural frequency of the system

A 0.453-Kg mass attached to a light spring elongates it by 7.87mm. Determine the natural frequency of the system.

  A rectactangular surface is placed in a vertical position

a rectactangular surface is placed in a vertical position in fresh water with its top and bottom edges horizontal. if

  If the packages come to rest at c calculate the constant

packages enter the 10ft chute at a with a speed of 4ftsec and have a 0.3g acceleration from a to b. if the packages

  A cylindrical bar of radius 15 mm and length 100 mm is held

a cylindrical bar of radius 15 mm and length 100 mm is held at both ends. if at 30 degc no axial force exists in the

  An ideal gas goes through an expansion process where the

helium gas expands from 125 kpa 350k and 0.25m3 to 100 kpa in a polytropic process with n 1.667 or 53. is the work

  Calculate the power output in kw

Air enters a turbine at 40 kN/m2, 900 C, and leaves at 10 kN/m2. The flow is reversible and adiabatic. Inlet velocity is quite low and outlet velocity is 150 m/s through a cross-sectional area of 0.20 m2. Calculate the power output in kW.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd