Estimate the time between when the concentration ratios

Assignment Help Civil Engineering
Reference no: EM13320570

A conservative tracer is applied to the ground surface and leached through the vadose zone by rainfall. The average volumetric water content is 0.40 over the upper 4 meters and 0.30 over the remaining 3 meters above the water table and the net infiltration rate (Darcy velocity) is estimated to be 22 cm/yr. If the dispersivity is estimated to be 8 cm, estimate the time between when the concentration ratios of C/Co = 0.1 and C/Co = 0.9 reach the water table (where Co is the initial tracer concentration).

Reference no: EM13320570

Questions Cloud

Determine the minimum size of the pad footing 2 metre wide : Determine the minimum size of the pad footing 2 metres wide for a steel column if a factor of safety of 2.0 is recommended (include an estimate of self weight of the footing in your calculations). The total load of the column is 447.644kN
Determine the longest wavelength of light : What is the longest wavelength of light that may be absorbed by a hydrogen atom that starts in the second excited state
Promotes value of complementary and alternative approach : In the health media, including the Internet, we are often exposed to news and opinion related to complementary medicine. This includes content that promotes the value of complementary and alternative approaches to health, such as acupuncture, ..
Will the quality of the coarse aggregate increase : To adjust the mix so as to increase the compressive strength, the water-to-cement ratio is reduced to 0.45. Will the quality of the coarse aggregate increase, decrease, or stay the same
Estimate the time between when the concentration ratios : The average volumetric water content is 0.40 over the upper 4 meters and 0.30 over the remaining 3 meters above the water table and the net infiltration rate (Darcy velocity) is estimated to be 22 cm/yr.
Different cultural perspectives begin working on a problem : When people from different cultural perspectives begin working on a problem, they have a hard time seeing each other's point of view and diversity issues keep some work groups from performing at their maximum effectiveness
Discuss how and why actual volume pumped would differ : A cylindrical volume of soil contaminated with trichloroethylene (TCE). It is about 2.5 m deep and about 4.0 m in diameter. The porosity of the soil is approximately 0.25.
The foundation for health and illness : Learning activity is designed to help you gain insights into yourself and also into key socio-medical constructs that are the foundation for health and illness.
What is the ending work in process inventory balance : Crockett Company uses a job costing system and had a beginning work in process inventory balance of $33,200. During the year, $57,000 of direct materials was placed into production.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the momentum change of a person with a mass

Suppose that a person who boards the elevator on the ground floor gets off on the fifth floor. Assuming that the elevator has achieved operating speed by the time it reaches the second floor and that it is still moving at its operating speed as it..

  Determine the exit velocity of the gas mixture

Oxygen and methane are mixed at 250kPa absolute pressure and 100 degrees C. The velocity of the gases into the mixer us 5m/s. The density of the gas leaving the mixer is 2.2 kg/m^3. Determine the exit velocity of the gas mixture.

  Determine the pressure at the point in n per m2 gage

Near the point (x, z) =(3,2) in a flow with a zero y-component (v=0), the velocity component are described by u =3x-3z, and w = 6-4z+ x. The velocities u and w are in m/s and are in the x- and z- directions, respectively.

  Which material will be cheaper if you want factor of safety

A structural tension member of 10 ft. long with a square cross-section is subjected to a load of 120,000 lb. There is a choice between an aluminum alloy and structural steel, with the following information given for each.

  What is the easiest way to solve for the 2 unknowns

Are either of the Ax or Jx forces relevant to finding the tension between H and J. If so, what is the easiest way to solve for those 2 unknowns.

  What is the total delay per cycle and delay per vehicle

A left-turn movement has a maximum arrival rate of 200 veh/h. The saturation flow of this movement is 1400 veh/h. For this approach, the yellow time is 4 seconds, all red time is 2 seconds and total lost time is 3 seconds.

  Who has been offered a 5-year contract at a remote location

Suzanne is a recent chemical engineering graduate who has been offered a 5-year contract at a remote location. She has been offered two choices. The first is a fixed salary of $75,000 per year.

  What is the value of the kinetic coefficient of friction

a 2kg moves down a 45 degree incline at a constant velocity of .1m/s. What is the value of the kinetic coefficient of friction between the object and the incline

  Determine the forces that occur on the l5-s1 joint

Determine the forces that occur on the L5/S1 joint if a person has a bent posture with hips flexed at 65 Degrees with no load. The distance from Upper Body Center of Gravity to L5/S1=30cm.

  Determine the speed of the collar when it has moved

Springs AB and CD have a stiffness of k = 300 N/m and k' = 200 N/m, respectively, and both springs have an unstretched length of 600 mm. If the 2-kg smooth collar starts from rest when the springs are unstretched

  What is the maximum weight that can be suspended on poll

What is the maximum weight that can be suspended on a 16 Kg poll, 3/5 from the end. The maximum tension of the 30 degree guy-wire is 1500 N. Find the horizontal and vertical forces exerted on the poll by the hinge.

  Minimizing the tension tab

What should TAC , TAB and the acute angle ? between TAB and the vertical to minimize the tension TAB ? Take o and W = 1,000 N. Hint: Consider various possible force triangles and decide on inspection how to minimize TAB.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd