Estimate the terminal velocity

Assignment Help Civil Engineering
Reference no: EM131012955

Estimate the terminal velocity of a 1.5-mm plastic sphere in oil. The oil has a specific gravity of 0.95 and a kinematic viscosity of 10-4 m^2/s. The plastic has a specific gravity of 1.07. The volume of the sphere is given by piD3/6.

Reference no: EM131012955

Questions Cloud

Calculate the uniformity coefficient : Using the Unified Soil Classification System of the U.S. Army Corps of Engineers, classify the soil. (The fines are easy to crumble when dry and has rapid reaction when shaken.)
Write an expression that represents cost per movie rental : Write a rational expression to represent how much of the project Jan will complete in x hours - how much of the project will Rebekah complete every hour and Write a rational expression to represent how much of the project Rebekah will complete in x h..
Lyon declared dividends : Lyon declared dividends of $6,000 on preferred stock and $17,280 on common stock. At the beginning of 2013, 10,000 shares of common stock were outstanding.
Estimate the fatigue strength of a rotating-beam made : Estimate the fatigue strength of a rotating-beam made of AISI 1035 CR steel corresponding to a life of 10^5 cycles of stress reversal. Also, estimate the life of the specimen corresponding to stress apmlitude of 60 ksi.
Estimate the terminal velocity : Estimate the terminal velocity of a 1.5-mm plastic sphere in oil. The oil has a specific gravity of 0.95 and a kinematic viscosity of 10-4 m^2/s. The plastic has a specific gravity of 1.07. The volume of the sphere is given by piD3/6.
Describe and explain the factors that affect the marble : Describe and explain the factors that affect the marble as it moves through your roller coaster. Describe the energy and momentum changes that will occur as the marble moves through the roller coaster, collides with the pendulum, and impa..
Find the velocity and acceleration of object after two sec : Motion of an Object The position of an object moving along a straight line is given by s=t √(2t2+1) (0 ≤ t ≤ 5). where s is measured in feet and t in seconds. Find the velocity and acceleration of the object after 2 sec.
How rapidly is radius of the spill increasing : Oil spilled from a ruptured tanker spreads in a circle whose area increases at a constant rate of 5.5 mi2/hr. How rapidly is radius of the spill increasing when the area is 11 mi2?
Find the slope and deflection at b : Find the slope and defliction at B For the cantilever beam shown here with evenly distributed load Ohm on the first 2/3 of the beam (A-B), and concentrated load at the end, C: P = 2ωa/3. Find the slope and deflection at B.

Reviews

Write a Review

Civil Engineering Questions & Answers

  I want to know how to draw bending moment diagram for this

i want to know how to draw bending moment diagram for this shape and the value of the moment in critical sections

  Explain how to estimate the los at the corridor

An airport corridor is 30 ft wide. given a peak demand of 300 pedestrians per minute and an average walk speed of 3 ft/s, estimate the LOS at the corridor

  Determine the normal depth yo and critical depth yc

A 1 m diameter unfinished concrete pipe (n = 0.015) has a slope of So = 0.001 and conveys water at Q = 0.5 m3/s. Find the normal depth yo and critical depth yc.

  Determine what is the viscosity of the oil

The distance between the piston and the cylinder is .0011 inch. If the piston decelerates at 1.85 ft/s^2, when the speed is 19.5 ft/s. What is the viscosity of the oil. cylinder is 6 in high and 5 in long.

  Determine the final speed of the cart

Two men A and B, each having a weight of 160lb stand on a200lb cart. Each runs with a speed of 3ft/s measured relativeto the cart. Determine the final speed of the cart if:

  Calculate the hydraulic conductivity of this clay

A falling-head permeability test was carried out on a clay soil of diameter 100 mm and length 150 mm. In 4 minutes the head in the standpipe of diameter 5mm dropped from 680 to 350 mm. Calculate the hydraulic conductivity of this clay.

  Explain the observed behaviour of the polyethylene sheet

Sandwhich structures are obviously very efficient in bending applications. Would they be equally efficient in tensile or compressive loading? Explain your answer in terms of area available for carrying tensile-compressive loads.

  What is the composition of the ß phase

A hypothetical A-B alloy of composition 40 wt%B-60 wt%A at sometemperature is found to consist of mass fractions of 0.66 and 0.34for the αand β phases, respectively. If the composition of the α phase is 13 wt% B-87 wt% A, what is the composition ofth..

  Determine max speed of the bicycle neglect rolling friction

The specific weight of aire is .075 lb/ft^3. The physiological limit of the power for this well trained cyclist is .5 hp (1hp=550 ft*lbs/s) Neglect rolling friction, find the max speed of the bicycle.

  If the streamwater contains 8 mg of dissolved oxygen

At a plant making MSG (monosodium glutamate) for use inAsian cooking the waste stream discharged to a nearby streamcontains 100 mg of glutamic acid(C5H9O4N) per liter

  Determine perpetual equivalent annual worth at interest rate

The cash flow associated with landscaping and maintaining a certain monument in Washington, D.C., is $100,000 now and $50,000 every 5 years forever. Determine its perpetual equivalent annual worth (in years 1 through infinity)

  Determine what is the decrease in thickness of the 6-ft fill

A loose, uncompacted sand fill 6 ft in depth has a relative density of 40%. Laboratory tests indicated that the minimum void ratios of the sand are 0.46 and 0.90, respectively. The specific gravity of solids of the sand is 2.65.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd