Estimate the temperature and overall carbon content of steel

Assignment Help Mechanical Engineering
Reference no: EM131274918

1. A steel is heated until 85% austenite, with a carbon content of 1.05%, forms. Estimate the temperature and the overall carbon content of the steel.

2. Why are the distances between lamellae formed in an eutectoid reaction typically separated by distances smaller than those formed in eutectic reactions?

Reference no: EM131274918

Questions Cloud

Describe hardness and microstructure in an eutectoid state : Describe the hardness and microstructure in an eutectoid steel that has been heated to 800°C, quenched to 650°C, held for 500 s, and finally quenched to room temperature.
How can h-d realign its diversification strategy : Create a Feasibility Study for Harley-Davidson using the following outline. How can H-D realign its diversification strategy to achieve a competitive advantage?
External and internal firewall in a table format : Present the rules for the external and internal firewall in a table format. a) Email may be sent using SMTP in both directions through the firewall, but it must be relayed via the DMZ mail gateway. External email must be destined for the DMZ mail ..
What is a ttt diagram : Why is it that a eutectoid steel exhibits different yield strengths and % elongations, depending upon if it was cooled slowly or relatively fast?
Estimate the temperature and overall carbon content of steel : Why are the distances between lamellae formed in an eutectoid reaction typically separated by distances smaller than those formed in eutectic reactions?
Identify the top two leadership points you would want : Identify the top two leadership points you would want to share at the workshop, and discuss why you selected those points. Address additional leadership traits that can assist in managing conflict and improve communication within the organization.
How do criminologists define white collar crime : Compare and contrast the positivistic and humanistic approaches to the study of white collar crime. Describe how educational institutions have defrauded students by not providing them with the quality of education promised. Identify the four approach..
Estimate the carbon content of the steel : A steel is heated until 40% austenite, with a carbon content of 0.5%, forms. Estimate the temperature and the overall carbon content of the steel.
Is the paper free of misspellings and typos : What theory did the author use to examine this topic and how did they use it? This question is most important for our purposes and should constitute the majority of the essay.Your thesis statement should reflect the theory you see at work in the a..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The initial pressure is 100 kpa and the initial temperature

air contained in a cylinder fitted with a piston is compressed in a quasi-equilibrium process. during the compression

  The water emerges from the boiler and flows into the

water at 10 kpa and 40 c enters the pump of a rankine cycle. the pump has an effiiciency of 82 and pumps the water up

  What is the loss for an anodized aluminum reflector

What is the reflectance loss in a 50% truncated CPC collector using silver mirrors if it has a 36° acceptance half-angle? What is the loss for an anodized aluminum reflector?

  After 10 lbhr of the oil is removed from the potato chips

after 10 lbhr of the oil is removed from the potato chips in the separation unit what is the mass fraction of oil on

  If the bottle on the conveyor of the above problem has a

1 a bottle filled with soda rests on the conveyor of a grocery check-out. the bottle weights 2 lbs the cg is 8 inches

  Calculate the average flow rate in the column

calculate the average flow rate in the column

  Use simulink to do the simulations of the step responses

Write down the transfer function of a third-order system with unity steady-state gain which has a real pole at s = -1 and a pair of complex poles at s = -1 +- ja. Simulate the open-loop step response of the system for 'a' values of 1, 2, 4, and 10, a..

  A 3084-kg steel projectile is fired from a gun at a

a 3.084-kg steel projectile is fired from a gun. at a particular point in its trajectory it has a velocity of 300 ms an

  Determine velocity v and direction of the combined jet

Two water jets in a horizontal plane collide and form one homogeneous jet as shown in Fig. Determine the elocity, V, and direction, θ, of the combined jet.

  The 10-kg sphere c is released from rest when theta0 and

the 10-kg sphere c is released from rest when theta0 and the tension in the spring is 100 n. determine the speed of the

  Calculate the extra separation at the saw cut

A steel ring of mean diameter 250 mm has a square section 2.5 mm by 2.5 mm. it is split by a narrow radial saw cut. the saw cut is opened up further by a tangential separating force of 0.2 N. calculate the extra separation at the saw cut. E = 200G..

  Estimate the electric power requirement

Use these results to estimate the area of silicon solar cells required to satisfy the community power requirements. Write a short narrative discussing your assumptions and analysis.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd