Estimate the surface temperature of the pod when suspended

Assignment Help Mechanical Engineering
Reference no: EM13634748

A spherical, underwater instrument pod used to make soundings and to measure conditions in the water has a diameter of 85 mm and dissipates 300 W.

(a) Estimate the surface temperature of the pod when suspended in a bay where the current is 1 m/s and the water temperature is 15oC.

Reference no: EM13634748

Questions Cloud

The formation of so3 from so2 and o2 is an intermediate : the formation of so3 from so2 and o2 is an intermediate step in themanufacture of sulfuric acid and it is also
For a one-tailed hypothesis test the critical z-value of : for a one-tailed hypothesis test the critical z-value of the test statistic is -1.48. which of the following is true
A 240 -v water heater has a resistance of 24 omega what : a 240 -v water heater has a resistance of 24 omega. what must be the minimum rating of the fuse in the circuit to
What is the decision rule at the 001 level of significance : a manufacturer wants to increase the absorption capacity of a sponge. based on past data the average sponge could
Estimate the surface temperature of the pod when suspended : a spherical underwater instrument pod used to make soundings and to measure conditions in the water has a diameter of
Using a 5 level of significance and a sample size of 26 : using a 5 level of significance and a sample size of 26 what is the critical value for a one-tailed hypothesis
The table below lists the numbers of audience impressions : the table below lists the numbers of audience impressions listening to songs and the corresponding numbers of albums
Two beetles run across flat sand starting at the same point : two beetles run across flat sand starting at the same point. beetle 1 runs 0.46 m due east then 0.75 m at 31o north of
Determine the maximum temperature that the lake could : a lake can freeze even if the temperature is above freezing. assuming a gentle breeze wind produces a convective heat

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The undeformed length of the spring is l knowing that the

a spring ab of constant k is attached to a support a and to a collar of mass m. the undeformed length of the spring is

  Find a the volumetric flow rate at inlet 1 in m3s b the

water at inlet 1 to a heat exchanger enters the heat exchanger through a circular pipe at a temperature of 200 oc a

  Calculate the engineering strain

A tensile specimen of cartridge brass sheet has a cross section of 0.320 in. × 0.120 in. and a gage length of 2.00 in. Calculate the engineering strain that occurred during a test if the distance between gage markings is 2.35 in. after the test.

  Helium is throttled from 12 mpa 20degc to a pressure of

helium is throttled from 1.2 mpa 20degc to a pressure of 100 kpa. the diameter of the exit pipe is so much larger than

  The a-36 steel axle is made from tubes ab and cd and a

the a-36 steel axle is made from tubes ab and cd and a solid section bc. it is supported on smooth bearings that allow

  A vessel contains 4 kg of wet steam liquid-vapor mixture at

a vessel contains 4 kg of wet steam liquid-vapor mixture at 140 degc. after the addition of heat the steam has a

  Determine the number of kmols of carbon monoxide contained

determine the number of kmols of carbon monoxide contained in a 0.27 m3 compressed gas cylinder at 200psi and 72f.

  A single-effect evaporator system with thermal

a single-effect evaporator system with thermal recompression is being used to concentrate skim milk from an initial

  Determination of the heat transfer coefficient values

this would provide you with a set of Reynolds numbers. Next, using the integral method, determine the velocity profiles within the boundary layer to be followed by determination of the heat transfer coefficient values for your selected Reynolds numbe..

  Find the velocity of the stream issuing out of the nozzle

two streams of air one at 1 bar 27degree and velocity of 30 ms and the other at 5 bar 227 degree and 50 ms velocity mix

  Draw a thermal circuit and calculate all the surface and

a 1.8 m x 1.5 m composite wall separates a furnace from the rest of the room in which it is located. the wall is made

  What are the angles

solution of oblique-angled triangle all threesides known two side at 7.5 in. and base at .3437 in. what are the angles ?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd