Estimate the ship speed

Assignment Help Mechanical Engineering
Reference no: EM13216596

A ship uses a kite to assist propulsion and reduce fuel consumption. The ship is 120 meters long, with a wetted area of 2800 m^2. The kite area is 330 m^2 and a force coefficient of 0.8. The kite cable makes an angle of 25 degrees with the horizontal. The velocity of the wind is 30 miles/hour. Neglect ship wave drag.

Estimate the ship speed

a) due to the kite only
b) with the propeller delivering 1250 hp to the water and using kite

 

Reference no: EM13216596

Questions Cloud

What would be the effect on the calculated value : what would be the effect on the calculated value of the vane efficiency for mass of jockey in error by 0.001 measurements.
Devise and evaluate the exergetic efficiency for cycle : Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given in the table below.For k=1.4 Cv=0.718kJ/(kg*k), and Cp= 1.005 kJ/(kg*K)
Find out the flexible budget materials cost : Determine the actual materials cost incurred for the completion of the 4800 pairs of glasses and compute the total materials variance.
Determine the temperature and the mass of the vapor in : piston cylinder device contains 0.06 m3 of saturated water vapor at 350 KPa pressure. Determine the temperature and the mass of the vapor in.
Estimate the ship speed : The kite cable makes an angle of 25 degrees with the horizontal. The velocity of the wind is 30 miles/hour. Neglect ship wave drag.
Adapt their marketing strategy to fit local conditions : International companies must decide how much to adapt their marketing strategy to fit local conditions. Discuss the advantages and disadvantages of standardization and localization strategies.
Find the z score values that separate : For a normal distribution, find the z score values that separate
What is the correct decimal notation for the number : What is the correct decimal notation for the number 1.345 x 10-1?
Cohesiveness and effectiveness : How can the appreciation and encouragement of people to be themselves and share their thoughts result in cohesiveness and effectiveness?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compute the maximum bending stress at mid-span

Calculate the maximum bending stress at mid-span, and, for the same section, locate the neutral axis. Neglect the weight of the beam

  Develop a dynamic model of a trebuchet

Analysis of the motion of swing including velocity and acceleration plots of all moving parts and projectile analysis of projectile eg: flight path, horizontal distance, deceleration and launch velocity

  What is the rotating speed of the disk in rpm

A slotted disk and opto-interrupter outputs pulses at 62 HZ. The disk has only one slot cut in it. what is the rotating speed of the disk in rpm?

  Find the maximum temperature in wall

The heat transfer convection coefficient between the wall and the fluid is 500 W/m2.K. Find the maximum temperature in wall.

  Probabilistic hough transform in big o notation

Probabilistic Hough transform in big O notation

  What is the rate of heat loss to the ambient

The external heat transfer coefficient is h=10 W/m^2*K. What is the rate of heat loss to the ambient?

  Calculate the final temperature in the small cylinder

If the filling is done rapidly, calculate the final temperature in the small cylinder, (a) assume that oxygen is an ideal gas with Cv= 5R/2 and (b) using accurate thermodynamic data for oxygen.

  Applied loads and young''s modulus and poisson''s ratio

Applied Loads, Young's modulus, Poisson's ratio, The Young's modulus and the Poisson's ratio for copper are 124.8 GPa and 0.36 respectively. When a tensile load is applie to a 1.5cm diameter copper rod

  What option is more economical

The annual holding cost rate for this type of item has been estimated at 28%. What option is more economical?

  Determine the velocity of the airplane required for pilot

Determine the velocity of the airplane required for pilot to experience weightlessness at the top of the circular path.

  Determine the final temperature of the water

one part of the tank contain 2.5 kg of compressed liquid water at 60 C and 600 kPa while the other part is evacuated. the partition is now removed, and the water expands to fill the entire tank. Determine the final temperature of the water and the..

  Supposing the plant operates on the ideal vapor-compression

Assuming the plant operates on the ideal vapor-compression cycle using refrigerant 134-a between the pressure limits of 120 and 700 kPa, determine

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd