Estimate the rate of heat transfer from the compressor

Assignment Help Civil Engineering
Reference no: EM13304726

50 kmol per hour of air is compressed from p1 = 1.2 bar to P2 = 6.0 bar in a steady-flow compressor. Delivered mechanical power is 98.8KW. Temperature and velocities are: T1= 300K T2= 520K u1= 10m s^-1 u2= 3.5m s^-1 Estimate the rate of heat transfer from the compressor. Assume for air that Cp = 7/2 R and that enthalpy is independent of pressure.

Reference no: EM13304726

Questions Cloud

Determine the cost c of the turbine for mass flow : Ethylene enters a turbine at 10 bar and 450 K, and exhausts at (atm) and 325 K. For mass flow in = 4.5 kg s^-1, determine the cost C of the turbine. State any assumptions you make. Data: H1 = 761.1 , H2 = 536.9 kg^-1, C/$ = (15,200)(1W1/kW)^0.573
Compute the mass of the air : An apartment has a living room whose dimensions are 2.9 m x 4.9 m x 6.0 m. what is the mass (in grams) of the air
Draw a schematic and show the control volume have selected : Refrigerant 22 is used in the evaporator pipe of a commercial refrigeration unit. At steady state it flows at a rate of 0.5 kg/s through the pipe of constant diameter. It enters the pipe at -­10C with a velocity of 5 m/s and a quality of 25%.
Compute the net charge contained by the cube : a closed Gaussian surface in the shape of a cube of edge length 3.35 m. What is the net charge (in Coulombs) contained by the cube
Estimate the rate of heat transfer from the compressor : 50 kmol per hour of air is compressed from p1 = 1.2 bar to P2 = 6.0 bar in a steady-flow compressor. Delivered mechanical power is 98.8KW. Temperature and velocities are: T1= 300K T2= 520K u1= 10m s^-1 u2= 3.5m s^-1
Calculate the work necessary to compress air in cylinder : Calculate the work necessary to compress air in an isolated cylinder from a volume of 6 ft^3 to a volume of 1.2 ft^3. The initial pressure and temperature are 30.0 psia and 50 degree F, respectively.
Determine how many nuclei are in the beam : A beam of nuclei is used for cancer therapy. Each nucleus has an energy of 181 MeV, How many nuclei are in the beam
Personal protective equipment : Complete the activity on page 250 and determine the proper response to the needs for personal protective equipment and how to protect workers in confined spaces.
Calculate entropy increase assuming constant specific heat : A paddle wheel, inserted inserted into the volume, does 720 KJ of work on the air. If the volume is 2 cubic meters, calculate the entropy increase assuming constant specific heats.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Draw elevation, plan and development of the lateral surfaces

Axis of the hole is perpendicular to VP. Draw elevation, plan and development of the lateral surfaces of the pyramid.

  Determine how high an elevated reservoir must be

Often times, this pressure comes from the fact that community's water supply is stored in an elevated reservoir. Determine how high an elevated reservoir must be so that the water supply has a pressure of 50 psi. Given: the unit weight of water is..

  What fraction of the load p is transmitted by the middle bar

The two outer bars (material A) are identical. The cross- sectional area of the middle bar (material B) is 31.544% larger than the cross- sectional area of one of the outer bars. Also, the modulus of elasticity of material A is twice that of mater..

  Determine the change in length of the steel bar

A steel bar of length 30 inches and circular cross section whose diameter varies linearly from 0.50 inches at one end to 0.75 inches at the other is subjected to an axial tensile force of 4.5 kip. Find the change in length of the bar.

  Which pipe would be suggested to the axis chemical company

Axis Chemical Company needs you to design a gravity sewer to convey 1,750 GPM of toxic waste. The pipe is to be glass-lined reinforced concrete (n = 0.009). Which pipe would you suggest the Joker use

  Determine what is the first-order decay rate constant

A minimum contact time of 30 min is required to reduce the pathogen concentration from 100 pathogens/L to below 1 pathogen/L through a first-order decay process. You plan on treating water at a rate of 1,000 gal/min.

  Largest principal stresses and maximum shear stress

The shaft diameter is 100 mm. Calculate the largest principal stresses and maximum shear stress that will occur in the shaft.

  Calculate concentration of dnapl in the water as function

If clean groundwater flows through an aquifer contaminated with a dense non- aqueous phase liquid (DNAPL), calculate the concentration of DNAPL in the water as a function of time if the DNAPL is dissolving into the water at a rate of k1

  Determine what is the instrumental and statistical error

During an experiment, the depth of a water flow in a flume is measured five times by using a ruler with 1/16-in division. The results from these measurements are 4.88 in, 5.06 in, 5.03 in, 5.13 in, 4.94 in. What is the instrumental error and what ..

  Calculate the mass emissions rate of no2

Assuming that the average stack gas velocity is 10.0m/s and the stack is circular with a 3.0 meter diameter, calculate the mass emissions rate of NO2 in kg/day.

  What type of aquifer material do expect in the location

A dye test reveals that the specific discharge between the two wells is about 2.75 m/day. if the wells are 45m apart, What type of aquifer material do you expect in this location

  Determine the flow rate and the normal depth in the channel

A reservoir discharges into a long trapezoidal channel with a bottom width of 20 feet, 3 to 1 side slopes, a bottom slope 0.001 and a roughness coefficient of 0.025 the reservoir surface is 10 feet above the invert at the channel entrance

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd