Estimate the radiant heat transfer from the wire you can

Assignment Help Mechanical Engineering
Reference no: EM13624739

1) A 10-cm long and 20-cm wide circuit board is covered with 100 closely spaced chips, each generating heat at a rate of 0.08 W and transferring it by convection to the surrounding air at 25°C. Heat transfer from the back surface of the board is negligible. What is the average surface temperature of the chips? The convective heat transfer coefficient on the surface of the board is 10 W/(m^2 K) and radiative heat transfer is negligible.

2) Toasters, blow dryers, and electric space heaters do their jobs via electric resistance heating: when electricity flows through a high-resistance wire, the temperature of the wire goes up, and heat is dissipated from the wire to the surroundings. A particular toaster uses 20 feet of a Nichrome resistance wire to cook toast. The diameter of the wire is 0.0285 inches.

a. Estimate the radiant heat transfer from the wire. You can assume that the surface temperature of the wire is approximately 750°C and that the wire is a thermal black body.
b. About how much current will this toaster use when connected to a 110 V power source?

Reference no: EM13624739

Questions Cloud

By what factor would the tension in a violin string have to : by what factor would the tension in a violin string have to change to tune it from baroque pitch of 415 hz to the
Determine the radius of curvature of the trajectory and the : a ball is released with the initial velocity of 80 ftsec at an angle of 35 degrees. determine the radius of curvature
When the three blocks are released from rest they : when the three blocks are released from rest they accelerate with a magnitude of 0.660 ms2. block 1 has mass m block 2
When the three blocks are released from rest they : when the three blocks are released from rest they accelerate with a magnitude of 0.660 ms2. block 1 has mass m block 2
Estimate the radiant heat transfer from the wire you can : 1 a 10-cm long and 20-cm wide circuit board is covered with 100 closely spaced chips each generating heat at a rate of
A ray of light in the coating is incident on the : a glass lens has a scratch-resistant plastic coating on it. the speed of light in the glass is 0.607c and the speed of
A recent study of how americans get to work revealed the : a recent study of how americans get to work revealed the following dataurbanruraltotalautomobile400200600public
If the data set was split into 5 sets 4 s long each what is : an accelerometer was used to measure the vibrations of machinery. the sensor output was acquired during an experiment
He would like a prescription for contact lenses to serve : a farsighted man uses eyeglasses with a refractive power of 2.15 diopters. wearing the glasses 0.02 m from his eyes he

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd