Estimate the power the device can produce at a wind speed

Assignment Help Civil Engineering
Reference no: EM13306880

The U.S. Department of Energy (DOE) constructed a Darrieus vertical-axis wind turbine in Sandia, New Mexico. The machine is 60.0-ft tall and 30.0-ft in diameter, and swept an area of 1200 ft 2. Estimate the power this device can produce at a wind speed of 20 miles/hr.

Reference no: EM13306880

Questions Cloud

How to call the function to update the statistics : A function which takes as in the parameters the three counters and displays them to the screen as shown in he example below.
What is the impedance of this circuit : A 150 ohm resistor, a 30 mH inductor and a 2 uF capacitor are connected in series with a 120 V rms source at 1500 Hz. What is the impedance of this circuit
Accounting reports are a major tool in business : Given Mountainarious Sporting Co.'s financial statements for the period 2004 to 2007 you are to undertake appropriate vertical, horizontal and ratio analysis of those financial statements
Explain different levels in a software organization : Give at least three examples of where decision making process could be used at different levels in a software organization.
Estimate the power the device can produce at a wind speed : The U.S. Department of Energy (DOE) constructed a Darrieus vertical-axis wind turbine in Sandia, New Mexico. The machine is 60.0-ft tall and 30.0-ft in diameter, and swept an area of 1200 ft 2.
Compute the wavelength of the scattered wave : A photon whose energy is 2.6 Ã- 10âˆ'14 J is scattered off an electron at an angle of 56â. What is the wavelength of the scattered wave
Calculate rate at which entropies of 2 reservoirs change : A completely reversible air conditioner provides 21,000Btu/h of cooling for a space maintained at 81degF while rejecting heat to the environmental air at 91degF.
Calculate the scattering angle : X-rays are scattered from electrons in a carbon target. The measured wavelength shift is 0.00099 nm. Calculate the scattering angle
Create queue class should have the following methods : create queue class should have the following methods:

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the momentum change of a person with a mass

Suppose that a person who boards the elevator on the ground floor gets off on the fifth floor. Assuming that the elevator has achieved operating speed by the time it reaches the second floor and that it is still moving at its operating speed as it..

  Find elevation difference in siphon crown nd downstream pool

The siphon crown is 1.2m above the water surface elevation of the reservoir and a length of 10m away from the siphon entrance. If the siphon diameter is 30 cm, the friction factor is 0.2, and the head loss coefficients are 0.2 inlet and 0.1 exit,

  Calculate specific internal energy of water leaving valve

Water is at 9000 kPa and 300 degrees celcius and flows through a partially open valve. Pressure immediately after the valve is measured to be 600 kPa. Calculate the specific internal energy of the water leaving the valve

  Determine pressure drop in length assuming laminar flow

Under these conditions flow is expected to be turbulent, but for a clean air, very smooth enterance (with guided vanes) to the tube and no tube vibration, it may be possible to maintain laminar flow.

  Find the location-velocity and acceleration of a box

The motion of a box on a spiral conveyor is defined by the following position vector: r = 0.5sin(2t) i + 0.5cos(2t) j - 0.2t k where r is in meters and t is in seconds. Find the location, velocity, and acceleration when t = 0.8 s.

  Question in structure analysis

Determine axial force and Max bending - Question in structure analysis

  Design for the maximum allowable slope pf the channel bed

The channel, which will be unlined, is to carry discharge of 1250 cfs under uniform flow condition and the velocity is not to be exceed 5 ft/sec. Design for the maximum allowable slope pf the channel bed.

  Calculate the wet density in pounds per cubic feet

A small chunk of the original sample had a wet weight of 140.9 grams and weighed 85.2 grams after drying. Compute the water content, using the correct number of significant figures.

  Estimate how often it will take more than 75 min to repair

Data from service records show that the time to repair a certain machine is normally distrubuted with a mean of 65 min and a standard deviation of 5 min. Estimate how often it will take more than 75 min to repair a machine.

  Survey with construction applications

The calculation and layout of horizontal and vertical curves should be done only by experienced surveyors and differential leveling measurements

  Determine the x and y scalar components

The forces F1, F2, and F3, all of which act on point A of the bracket, arespecified in three different ways. Determine the x and y scalar components of each of the three forces.

  What is the dry unit weight of this material

A soil borrow material in its natural state in the ground has a unit weight of 118pcf. Its natural water content is 7%. What is the dry unit weight of this material?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd