Estimate the net power output of the plant in btuh if the

Assignment Help Mechanical Engineering
Reference no: EM13630812

At a particular location in the ocean, the temperature near the surface is 80oF, and the temperature at a depth of 1500 ft is 46oF. A power plant based on the Rankine cycle, with ammonia as the working fluid, has been proposed to utilize this naturally occurring temperature gradient to produce electrical power. The power to be developed by the turbine is 8.2 X 108 Btu/h. A schematic diagram is shown. For simplicity, the properties of seawater can be taken as those of pure water.Assume the isentropic efficiency of the turbine is 80% and the isentropic efficiency of the pump is 70%. Assume that the ammonia leaving the boiler is saturated vapor and that the ammonia leaving the condenser is saturated liquid.

a.) Estimate the net power output of the plant, in Btu/h if the pumps used to circulate seawater through the evaporator and condenser heat exchangers require a total power input of 2.55 X 108 Btu/h.

b.) Determine the seawater flow rates through the boiler and condenser, in lb/h.

c.) Estimate the thermal efficiency of the proposed cycle and compare it to the thermal efficiency of a reversible power cycle operating between thermal reservoirs at 80 and 46oF.

Reference no: EM13630812

Questions Cloud

Find the entropy production rate for the nozzle the exit : the comubstion chamber of a liquid-h2liquid-o2 fueled rocket produces a steady-state-steady-flow of h2osuperheated
If you can neglect the potential energy effects the inlet : steam enters an adiabatic turbine at 3 mpa and 350 celsius and leaves the turbine at 75 kpa with a quality of 89. if
Nitrogen gas at steady-state-steady-flow undergoes a : nitrogen gas at steady-state-steady-flow undergoes a compression provess through a well-insulated compressor. the inlet
Argon gas flows through a rigid nozzle at : argon gas flows through a rigid nozzle at steady-state-steady flow. the inlet flow velocity is small. the gas exits the
Estimate the net power output of the plant in btuh if the : at a particular location in the ocean the temperature near the surface is 80of and the temperature at a depth of 1500
Describe fully what happens when you cools down a melt of : describe fully what happens when you cools down a melt of 40mol nio-60mol mgo. give the compositions of the phases and
10 mols of liquid benzene at 20degc and 1 bar is pumped to : 10 mols of liquid benzene at 20degc and 1 bar is pumped to 5 bar. at the inlet conditions the molar volume of benzene
How much power is delivered by the battery due to the : an automotive battery has an emf of 13.4 v. when supplying power to the starter motor the current in the battery is
Liquid water enters a 25-kw pump at 100kpa pressure at a : liquid water enters a 25-kw pump at 100kpa pressure at a rate of 5kgs. determine the highest pressure the liquid water

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd