Estimate the molar volume

Assignment Help Mechanical Engineering
Reference no: EM13708088

The Molar Volume of Al2O3 at 25 Degrees Celsius and 1 atm is 25.715 cc/mol. Its coefficient of thermal expansion is 26 x10^-6 K^-1 and the coefficient of compressibility is 8.0 x10^-7 atm^-1. Estimate the molar volume of Al2O3 at 400 degrees Celsius and 10 k bars pressure (10x10^3 atm).

Reference no: EM13708088

Questions Cloud

Determine the magnitude of the principal stresses at point : The maximum shear strain at a point in a thin elastic plate is given as gamma (max) = 450(mu). it is also known that the sum of the normal stresses on two perpendicular planes passing through the point is 30 mpa. Determine the magnitude of the princi..
Refrigerant gains heat it flows through pipe and leave pipe : Refrigerant 134a enters a 28-cm diameter pipe steadily at 200 kPa and 20C with a velocity of 5 m/s. The refrigerant gains heat as it flows through the pipe and leaves the pipe at 180 kPa and 40 C.
Calculate heat transfer : A rigid 15-L vessel initially contains a mixture of liquid water and vapor at 110 C with 11.2 qualities the mixture is then heated until the temperature is 155 C. Calculate heat transfer
Find expressions for the induced transverse stresses : A cube of linear elastic material is subjected to a vertical compressive stress sigma1 in the 1-direction, but it is now constrained ( e = 0) in both the 2- and 3- directions. Find expressions for the induced transverse stresses, sigma2 and sigma3 in..
Estimate the molar volume : The Molar Volume of Al2O3 at 25 Degrees Celsius and 1 atm is 25.715 cc/mol. Its coefficient of thermal expansion is 26 x10^-6 K^-1 and the coefficient of compressibility is 8.0 x10^-7 atm^-1. Estimate the molar volume of Al2O3 at 400 degrees Celsius ..
Calculate the average linear velocity : An aquifer has a hydraulic conductivity of 12 ft/day and an effective porosity of 17% and is under a hydraulic gradient of 0.0055 m/m. Calculate the specific discharge in m/s. Calculate the average linear velocity in m/s.
Determine the volume of the tank : A tank that volume is unknown is divided into two parts by a partition. One side of the tank contains 0.01 m3 of refrigerant R-134a that is a saturated liquid at 0.8 MPa, while the other side is evacuated. The partition is now removed, and the refrig..
Human body-what is the oxygen pumping rate in g per minute : Consider human body. A 70 kg human has about 5 L of blood and it is pumped by heart at about 5.2 LPM (liter of liquid blood per minute). At any given time, the lungs transfer oxygen from alveoli to blood capillaries and the oxygen concentration in bl..
Consists of two chambers separated by a frictionless piston : The double-acting piston cylinder shown below consists of two chambers separated by a frictionless piston. The piston is initially locked in place, dividing the device into two equal 1 m3 sub-chambers. Side A contains water at 90°C and a quality of x..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd