Estimate the heat transfer area of the heat exchanger

Assignment Help Mechanical Engineering
Reference no: EM13644765

An Ocean Thermal Energy Conversion (OTEC) system is proposed to generate 10 MW of electricity. The proposed location of the plant has an ocean surface temperature of 25 C and the cold water for the plant comes from 1000 m at a temperature of 5 C. If the actual efficiency of the plant is estimated to be 50% of the Carnot efficiency, determine the rate of thermal energy supplied to the plant by the ocean surface water. If the thermal energy supplied to the plant is obtained by pumping the surface ocean water through a heat exchanger where the temperature of the surface water drop by 5 C, determine the flow rate of surface water through the heat exchanger. If the heat exchanger has an overall heat transfer coefficient of 6000 W/m^2 K, estimate the heat transfer area of the heat exchanger. Assume that the ocean water has the same density and specific heat as those of typical water.

Reference no: EM13644765

Questions Cloud

Nj state partol would like to know if the mean speed that : nj state partol would like to know if the mean speed that drivers drive in i-80 is faster than i-280. they gather
In a water heating system cold water at 5 c flowing at a : in a water heating system cold water at 5 c flowing at a rate of 5 kgs is mixed adiabatically with hot water at 80 c
After the addition of 2000 ml of 0500 m standard koh : after the addition of 20.00 ml of 0.500 m standard koh solution to a 10.00ml sample of formic acid hcooh ka 1.8 x 10-4
The output y of a binary communication channel is a : the output y of a binary communication channel is a unit-variance gaussian random variable with mean zero when the
Estimate the heat transfer area of the heat exchanger : an ocean thermal energy conversion otec system is proposed to generate 10 mw of electricity. the proposed location of
What is the heat supplied to the plant by the steam if the : steamboat springs geothermal power plant in nevada operates between a steam temperature of 220 c and an ambient
500 trials where each trial consists of tossing four coins : 500 trials where each trial consists of tossing four coins and counting the number of heads. find the number of cases
A university wants to know whether there is a difference in : a university wants to know whether there is a difference in the proportions of female and male students in a two
A 102 x 10-3 microf capacitor has an initial charge of 0100 : a 1.02 x 10-3 microf capacitor has an initial charge of 0.100 c. when a resistor is connected across the capacitor

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd