Estimate the heat generated in the weld zone

Assignment Help Civil Engineering
Reference no: EM131407243

Calculate the range of allowable currents in Problem 31.43 if the temperature should be between 0.7 and 0.8 times the melting temperature of copper. Repeat this problem for carbon steel.

Problem 31.43

Two flat copper sheets (each 1.0 mm thick) are being spot welded by the use of a current of 7000 A and a current flow time of 0.3 s. The electrodes are 4 mm in diameter. Estimate the heat generated in the weld zone. Assume that the resistance is 200 μ Ω .

Reference no: EM131407243

Questions Cloud

How could you confirm or disprove your suspicion : Consider the situation where two round components are welded together. You believe that the components were friction welded, with the flash removed by machining. How could you confirm or disprove your suspicion?
Compare the different economic systems : Compare the different economic systems.Explain which economic system you would select.Include least two (2) sources within the body of your work.Format your assignment consistent with APA guidelines.
Comment on the credibility of the suppliers claim : The supplier claims that no more than 2% of the items in the shipment are defective. Carry out an appropriate hypothesis test and comment on the credibility of the supplier's claim.
Who wrote the seneca falls declaration : Who wrote the Seneca Falls Declaration? What inspired it? What is the (obvious) model for it? What, according to Mary Wollstonecraft, are the "negative" virtues? Compare these two documents. What grievances do they have in common? Are any remedies su..
Estimate the heat generated in the weld zone : Calculate the range of allowable currents in Problem 31.43 if the temperature should be between 0.7 and 0.8 times the melting temperature of copper. Repeat this problem for carbon steel.
Discuss the strengths of the us health care system : Despite the documented challenges that the U.S. health care system faces, it also enjoys a number of advantages over other systems around the world.Choose 2 other countries from around the world and discuss the strengths of the U.S. health care s..
Whether one tail test or two tail test would be appropriate : For each of the given situations, determine whether a one-tail test or a two-tail test would be appropriate. Describe the test, including the null and alternative hypotheses, then explain your reasoning in selecting it.
Why do you think cosmic or creation myths are important : Which world or worlds, such as sky, earth, and underworld, are represented in the myths you chose? What are the elements of these worlds?· Describe the creators. Are the creators male or female, and of what significance is gender? Describ..
Identify what would constitute a type i error : If a transit employee provides a strand of hair for drug testing, state the null and alternative hypotheses in verbal terms, then identify what would constitute a Type I error and a Type II error in this situation.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine shear stress in 25 by 50 cm rectangular section

Determine the shear stress in a 25 × 50 cm rectangular section if the shear force is 20 KN and torsional moment is 10 KN m at service loads. Assume M20 mix and 0.75% tension reinforcement at an effective cover of 50 mm.

  Three cylinders from the same mix were tested

Three cylinders from the same mix were tested for strenght.  Cylinders A and B were cast in 4x8 molds while cylinder C was cast in a 6x12 mold.  The total loads were as follows; cylinder A= 65,200 lbs.,  cylinder B= 68,550 lbs., cylinder C= 151,190 l..

  Determine the required minimum stiffness k

When the 100-lb block is at h = 3 ft above the cylindrical post and spring assembly, it has a speed of v = 20 ft/s. If the post is made of 2014-T6 aluminum and has a diameter of d = 2 in., determine the required minimum stiffness k of the spring s..

  How many kilograms of suspended solids are removed

The influent suspended solids concentration to a primary settling tank is 435mg/L. The average flow rate is 0.050m3/s. If the suspended solids removal efficiency is 60 percent, how many kilograms of suspended solids are removed

  Find correct horizontal distance considering a gentle slope

A civil engineer used a 30-m tape in measuring an inclined distance. The measured length on the slope was recorded to be 459.20 m long. The difference in elevation between the initial and the end point was found to be 1.25 m.

  Find the percentage of aceticacid ionized in the solution

One liter of a solution is made by adding 3grams of acetic acid (HAc) to distilled water. The molecular weightof acetic acid is 60.052. The acid dissociation constant for aceticacid

  Estimate the tensile strength of the wire and the work

A polycrystalline Al alloy contains a dispersion of hard particlesof diameter 10-8m and average center to center spacingof 6x10-8m measured in the slip planes. Estimatetheir contribution to the tensile yield strength,σy, of the alloy.

  Compounds empirical and molecular formula

A Silane contains 90.31 % silicon and 9.69 % hydrogen by mass. The compound has a molar mass of 62 g/mol. Determine the compound's empirical and molecular formula.

  Neglect the energy stored in the paddle wheel

A paddle wheel within the cylinder is rotated until 15 kJ of work is done on the air while the pressure is held constant. Determine the final temperature of the air. Neglect the energy stored in the paddle wheel.

  Determine the smallest wall thickness which may be used

A spherical pressurevessel of 1.2m outside diameter is to be fabricated from a steelhaving an ultimate stress of σU450 MPa. Knowing that a factor of safetyof 4.0 is desired and that the gage pressure may reach 3 MPa,

  Determine the corresponding values of

If the squirrel's speed is v = 2 m/s when the position s = 10m determine the corresponding values of .

  Determine the basic beam equilibrium equation

Determine the basic beam equilibrium equation (Ra + RB = W) and the principle of moments for finding beam reactions

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd