Estimate the force of the roof at the opening pressures for

Assignment Help Mechanical Engineering
Reference no: EM13624301

Fluid Mechanics for Chemical Engineers.Nevers

2-11Large Hydrocarbon storage tanks normally have a valve on their vents that allows free flow of air in or out when a liquid is being pumped in or out but that prevents air flow for small pressure differences caused by wind, solar heating of the tank, and changes in atmospheric pressure. these reduce the breathing losses of valuable hydrocarbons as well as the amount of atmospheric pollution.

These valves are typically set to open at an internal pressure of 4 inches of water and an external pressure of 2 inches of water.
a) Estimate the force of the roof at the opening pressures for internal pressure and for vacuum. -oil storage tank has a flat, horizontal, circular roof 120 feet in diameter.

b) Why is the setting larger for internal pressure than external pressure?

Reference no: EM13624301

Questions Cloud

Suppose you wish to estimate the difference between the : suppose you wish to estimate the difference between the mean acidity for rainfalls at two different locations one in a
If we were told that the water will reach a temperature of : a tank has a stirrer that delivers 200 kj of work on 100 kilograms of water at 45 degrees celcus. assume all of the
If we were told that the water will reach a temperature of : a tank has a stirrer that delivers 200 kj of work on 100 kilograms of water at 45 degrees celcus. assume all of the
The potential on the outer surface of the membrane is 516 : the membrane that surrounds a certain type of living cell has a surface area of 7.1 x 10-9 m2 and a thickness of 1.6 x
Estimate the force of the roof at the opening pressures for : fluid mechanics for chemical engineers.nevers2-11large hydrocarbon storage tanks normally have a valve on their vents
The relationship between pressure and volume during the : oxygen o2 gas within a piston-cylinder assembly undergoes an expansion from a volume v1 0.01 m3 to a volume v2 0.03
An ice chest is constructed of 04 mm thick plain-carbon : an ice chest is constructed of 0.4 mm thick plain-carbon steel plate a 1.9 cm thick layer of styrofoam k0.033 wm c and
If the charge in part a is due to k ions charge e how many : the membrane that surrounds a certain type of living cell has a surface area of 7.1 x 10-9 m2 and a thickness of 1.6 x
Draw the power curve and compute the probability of : a firm assumes that idle time of workers in construction projects is 72 minutes give or take 20 minutes. a random

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The pipe flow exits to the atmosphere neglecting minor

water is pumped through a horizontal 1500 m long section of steel commercial pipe with diameter of 5 cm. the pressure

  Find the temperature of source and sink

a heat engine working on carnot cycle converts 25% of heat into work when the temperature of the sink is reduced by 353 k the efficiency gets doubled .find the temperature of source and sink.

  Determine the work kj performed by the air in the cylinder

initially 0.05 kg of air is contained in a piston-cylinder device at 200 degc and 1.6 mpa. the air then expands at

  Inlet 1 is a saturated vapor with a flow rate of 034 kgs

1 air at the inlet of a nozzle is at 500 kpa 42.2oc and a velocity of 87 ms. the nozzle exit pressure is at 132 kpa.

  Compute the average acceleration of the air force fighter

the average accelerations of a us navy fighter jet takeoff to an us air force fighter jet takeoff are very different.

  A vehicle is moving along a straight line with an

a vehicle is moving along a straight line with an acceleration given by ms2 where s is in m. at s 0 t 0 and v 6 ms.

  What is the electrical power available

You are designing a remote-area power supply based on a miniature wind turbine that is 20% efficient. Meteorological data indicates an average wind speed of 24 km/h at an air temperature of 10oC and pressure of 0.9 atm. The rotor has a diameter of..

  Determine the efficiency and the horsepower output if the

a four-stroke-cycle engine operates on the air-standard diesel cycle. the engine has six cylinders with a 0.105 m bore

  Determine the volume flow rate and the density of the gas

carbon dioxide gas enters a pipe at 3 mpa and 500 k at a rate of 2 kgs. the gas is cooled at constant pressure as it

  Find the orthogonal rake angle of the cutting tool

the friction force acting at the chip-tool interface the main (tengential ) cutting force is 1500N . Find the orthogonal rake angle of the cutting tool?

  A constriction in a pipe will cause the velocity to rise

a constriction in a pipe will cause the velocity to rise and the pressure to fall at section 2 in the throat.nbspthe

  A 12-kg solid whose specific heat is 28 kjkg degree c is

a 12-kg solid whose specific heat is 2.8 kjkg degree c is at a uniform temperature of -10 degree c. for an environment

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd