Estimate the electrical power in watts that needs

Assignment Help Civil Engineering
Reference no: EM13561463

1.A fan produces a pressurerise of 6mm of water to move air through a hair dryer. The mean velocity of the air at the exit is 10 m/s, and the exit diameter is 44 mm. Estimate the electrical power in watts that needs to be supplied to operate the fan. Assume that the fan/motor combination has an efficiency of 60%.

2.A small town produces 0.15 MGD of wastewater. How many acres in size would an aerated lagoon need to be to treat this wastewater assuming a depth of 8 ft. and a detention time of 6 days? (7.48 gal/ft^3 ; 43,560 ft^2/acre)

Reference no: EM13561463

Questions Cloud

Determine the force supported by the hydraulic cylinder : A Steel plate weighing 205 lb with a center of gravity at point G is supported by a roller at point A,a bar DE, and a horizizontal hydraulic cylinder BC. Negelcting all weights of all members except for the plate,
What is the maximum acceleration from rest of the car : A car has a 10-ft wheelbase (L). the center of gravity is 18 inches about the ground and 5 ft behind the front axle. The weight of the car is 2500 lb. mechanical efficiency if the drivetrain is 85%. and the wheel radius is 15 inches
What is the rolling resistance of the road : A CAT 834H (rubber tires, high pressure), with an operating weight of 103,849 lbs, is pulled up a road whose slope is +3.0% at a uniform speed. If the average tension in the towing cable is 6,060 lb,
How much does the choice of the distribution affect : On a single graph, plot the PDFs if E is assumed to be normally, lognormally, and gamma distributed.  Plot the PDFs for E values between 10,000 and 50,000 kips/in2.  Make sure to label the axes and use a legend to label the curves.
Estimate the electrical power in watts that needs : A small town produces 0.15 MGD of wastewater. How many acres in size would an aerated lagoon need to be to treat this wastewater assuming a depth of 8 ft. and a detention time of 6 days? (7.48 gal/ft^3 ; 43,560 ft^2/acre)
What are the basic assumptions of the traffic flow model : Two 25-kip loads are maintained 6 ft apart as they are moved slowly across the 18-ft beam ab. write a computer program and use it to calculate the bending moment under each load and at the midpoint c of the beam for values of x from 0 to 24 ft at int..
Watch starwood: supply chain strategy : Watch “ Starwood: Supply Chain Strategy ” and read the video Case “Sourcing Strategy at Starwood” at the end of Chapter 12 in the textbook. Also review other source materials, including your textbook, related specifically to Starwood or other organiz..
Determine the volume of the aeration basin : An activated sludge system operates at a flow rate (Q) of 400 m3/day with an incoming BOD of 300 mg/L. The kinetic constants for this system are Y = 0.5 kg SS/kg BOD, Ks = 200 mg/L, ?
Calculate the fraction : And forms HCN, it will volatilize, and if it volatilizes, HCN can poison mine workers. At pH 10.4, what fraction of the cyanide is in the CN- form?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Consolidation ratio of the soil at the unloaded condition

An increment of vertical stress of150kpa compress the sample to a void ratio of1.43. What is the over consolidation ratio of the soil at the unloaded condition.

  Calculate the efficiency of an esp required to meet federal

Assume that 30% of the ash falls out as bottom ash in the furnace. Calculate the efficiency of an ESP (electrostatic precipitator) required to meet federal new source performance standards

  Determine to the nearest 1 by 4 in the smallest dimension h

If A and B are both made of wood and are 3/8 in thick, determine to the nearest ¼ in the smallest dimension h of the support so that the average shear stress does not exceed \tauallow = 300 psi.

  Determine the mass flow rate of the cooling water

Refrigerant 134a is compressed at steady state from 2.4 bar, 0 degrees celcius, to 12 bar, 50 degrees celcius. Refrigerant enters the compressor with a volumetric flow rate of 0.38m^3/min, and the power input to the compressor is 2.6 kW.

  What range of reactor volumes is necessary to achieve time

to achive a specific level of disinfection a water treatment plant operator determines the" Ct" value 180mg min/l is necessary with units for disinfectant concentration C in mg/l and disinfectant contact time t in minutes

  Estimate the theoretical fracture strength of a brittle

Estimate the theoretical fracture strength of a brittle material ifit is known that fracture occurs by the propagation of anelliptically shaped surface crack of length

  Determine the drawdown after 2 days of puming

a well is located in a confined aquifer. the transmissivity of the aquifer is 1200 m^2/d and the storativity is 0.0005. the flow rate is 4000 m^3/d. At a distance 75m from the well,

  Determine the force exerted on the tank bottom

A cylindrical water tank is suspended vertically by its sides. The tank has a 10-ft diameter and is filled with 20 degree celcius water to a 3-ft depth. Determine the force exerted on the tank bottom

  Define the control variables and formulate the mathematical

No more than 12 units of TV, 40 units of radio and 25 units of direct mail are available. A minimum of 9 units of radio and 5 units of direct mail must be purchased.

  Determine the torque that develops in the rod in in-lb

The end of a 0.75-in-diameter rod is fixed to an immovable plate. The length of the rod is 18.0 in. A 50-lb weight is attached to a 16.0-in lever at the end of the Rod so that the weight is hanging perpendicular to the longitudinal axis of the rod..

  Determine the normal stress in the aluminum shell

An axial force of 200 kN is applied to the assembly by means of rigid end plates. Determine the normal stress in the aluminum shell.

  Compute nominal compressive strength for a500 grade b steel

An HSS 10×8×3?16 is used as a compression member with one end pinned and the other end fixed against rotation but free to translate. The length is 12 feet. Compute the nominal compressive strength for A500 Grade B steel

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd