User Account

All Pages

Estimate the cooling capacity of absorption chiller to be

Assignment Help Mechanical Engineering
Reference no: EM13719879

A gas turbine (can assume an ideal Brayton cycle) has a pressure ratio of 10. It is connected to an electric generator with an efficiency of 95% which produces 300kW of electricity. The gas turbine burns natural gas with a heating value of 100,000 btu/therm. The waste heat from the gas turbine is used by an absorption chiller with a COP of 0.8. What would you estimate the cooling capacity of the absorption chiller to be?

Reference no: EM13719879

Questions Cloud

A material with a true stress strain curve : A material with a true stress strain curve? = 350 E0.25 MPa is used in wire drawing. Calculate the maximum reduction in cross sectional area per pass based on ideal conditions.
Calculate the net entropy change of the system : A hollow steel sphere with a 0.5 m inside diameter and a 2 mm thick wall contains water at 2MPa, 250°C. The system (steel plus water) cools to the ambient temperature, 30°C. Calculate the net entropy change of the system and the surroundings for this..
Determine the final mass in the cooker : A pressure cooker has a volume of 0.011 m3 and initially contains a two-phase liquid-vapor mixture of H2O at a temperature of 100o C and a quality of 10%. As the water is heated at a constant volume, the pressure rises to 2 bar and the quality become..
Rectangular unfinished concrete channel with a width : A rectangular unfinished concrete channel with a width of 18 ft conveys water at 350 ft3/s. The temperature of the water is at 30oC. The channel has a slope of 0.001. Determine the liquid depth for uniform flow. Is the flow supercritical or subcritic..
Estimate the cooling capacity of absorption chiller to be : A gas turbine (can assume an ideal Brayton cycle) has a pressure ratio of 10. It is connected to an electric generator with an efficiency of 95% which produces 300kW of electricity.
Assume an ideal brayton cycle : A gas turbine (can assume an ideal Brayton cycle) has a pressure ratio of 10. It is connected to an electric generator with an efficiency of 95% which produces 200MW of electricity. The gas turbine burns natural gas with a heating value of 100,000 bt..
What is the mass flow rate of steam through the turbine : Consider a small simple Rankine Power cycle which produces 600kW power from an electric generator with an efficiency of 95%. The steam leaves the boiler at 1250psia as superheated steam and leaves the turbine at 2 psia with a quality of 90%.
Vapor compression refrigeration cycle : A vapor compression refrigeration cycle has a theoretical COP of 4.8 and provides 120,000 btu/h of cooling (same as 10 tons of cooling). The compressor is driven by a motor with an efficiency of 92%. Estimate the theoretical kW electrical demand that..
Dam is to be built such that the estimated average flow : The dam is to be built such that the estimated average flow over its crest will be Q = 3000 m^3/s. Determine the required flow over the crest of a model built to a scale of 1/25

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A newly developed diagnostic test indicates that 80 of

a newly developed diagnostic test indicates that 80 of students predicted to score 100 on an exam actually do. the

  A piece of steel has a conductivity of k 15 wmk and a

a piece of steel has a conductivity of k 15 wmk and a brick has k1wmk. how thick a steel wall will provide the same

  In a heat exchanger 10 kgs of water enters the hot side at

in a heat exchanger 10 kgs of water enters the hot side at 73degc and leaves at 43degc. 19 kgs of water enters the cold

  Tom kicks the ball with a speed of 5ms horizontally and jim

tom and jim are kicking a ball which has a mass of 490g back and forth. tom kicks the ball with a speed of 5ms

  What is the mole fraction of water in the exhaust stream

A mixture of propane and butane is fed into a furnace where it is mixed with air. The furnace exhaust leaves the furnace at 343°C, 780.0 mmHg and contains only N2, O2, CO2, and H2O. The partial pressure of O2 in the exhaust is 51.40 mmHg and the part..

  What size of pipe would be required to move

what size of pipe would be required to move 30 milliliters of air in one minute at a pressure of 100 psi.

  Find denisty altitude

Find denisty altitude

  Consider five kilograms of water at 10degc and 75 quality

consider five kilograms of water at 10degc and 75 quality in a closed container. the water is compressed isentropically

  Converted at constant pressure to saturated steam

Liquid water is fed to a boiler at 24ºC and 10 bar is converted at constant pressure to saturated steam. Use the steam tables to calculate H (kJ/kg) for this process, and then calculate the heat input required to produce 15,000 m3/h of steam at the e..

  Determine for the steam exiting the tank

Three return steam lines in a chemical processing plan enter a collection tank operating at a steady state at 1 bar. Steam enters inlet 1 with flow rate of 0.8 kg/s and a quality of 0.9. Steam enters inlet 2 with flow rate of 2kg/s at 200 degrees C. ..

  A close rigid tanks with a volume of 2 m3 contain hydrogen

a close rigid tanks with a volume of 2 m3 contain hydrogen gas initially at 320 k and 180 kpa. heat transfer from a

  Asume that x0 01 m and xdot0 0 the dsplacement xt is

consider the sysstem shown in figure 3-45 where m 2 kg b 4 nxm and k 20 nm. assume that x0 0.1 m and xdot0 0. the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd