Estimate the amount of work that was required

Assignment Help Civil Engineering
Reference no: EM13890851

George Washington Gale Ferris, Jr., a civil engineering graduate from Rensselaer Polytechnic Institute, built the original Ferris wheel for the 1893 World's Columbian Exposition in Chicago. The wheel, an astounding engineering construction at the time, carried 36 wooden cars, each holding up to 60 passengers, around a circle 76 m in diameter. The cars were loaded 6 at a time, and once all 36 cars were full, the wheel made a complete rotation at constant angular speed in about 2 min. Estimate the amount of work that was required of the machinery to rotate the passengers alone. Assume each passenger had a mass of 58 kg.

Reference no: EM13890851

Questions Cloud

A paper on globalization and alternative energy : a paper on globalization and alternative energy
Calculate the amounts and compositions of phases : Calculate the amounts and compositions of phases and constituents of steel composed of iron and 0.10% carbon just above and below the eutectoid isotherm
Drainage facility : Drainage facility: - Drainage facility is the normal or fake evacuation of surface and sub-surface water from a territory. Numerous rural soils need waste to enhance creation or to oversee water supplies
Determine the volume fraction of fibers that will required : Using the data provided, determine the volume fraction of fibers that will be required. What will be the tensile strength of this composite? Assume that the matrix stress at fiber failure is 50 MPa (7250 psi)
Estimate the amount of work that was required : The cars were loaded 6 at a time, and once all 36 cars were full, the wheel made a complete rotation at constant angular speed in about 2 min. Estimate the amount of work that was required of the machinery to rotate the passengers alone
Prepare a journal entry to close out manufacturing overhead : Calculate the overapplied or underapplied overhead for the year. Prepare a journal entry to close out the Manufacturing Overhead account into Cost of Goods Sold.
Calculate the azimuths of the remaining sides : Balance the following interior angles (angles to the right) of a five-sided closed polygon traverse using method 1 of section 10.2. if the azimuth of side AB is fixed at 122-32-16, calculate the azimuths of the remaining sides
Determine the average penetration of the pile : The design capacity of a steel pile is 250 kN. The pile is driven by a steam hammer with a manufacturer's hammer energy rating of 36 kN • m. Determine the average penetration of the pile
Compute the firms predetermined overhead rate for the year : Compute the firm's predetermined overhead rate for the year using each of the following common cost drivers: (a) machine hours, (b) direct-labor hours, and (c) direct-labor dollars.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the f per m ration for the aeration tank

An activated sludge process receives 4000m^3 / day containing 120 mg BOD /L from the primary settling tank and 3500 m^3/day Containing 25mg BOD/L from the secondary settling tank.

  Estimate the time between when the concentration ratios

A conservative tracer is applied to the ground surface and leached through the vadose zone by rainfall. The average volumetric water content is 0.40 over the upper 4 meters and 0.30 over the remaining 3 meters above the water table

  Explain the working principles of two tests that can

Should the soil be compacted at the dry of optimum or at the wet of optimum condition in order to minimize the swelling potential? Briefly explain the reason for your answer.

  How much larger should street name be in order to be legible

street nam sizes on the signs at a certain location can be discerned by a person with 20/40 vision from a distance of 300 ft. how much larger should the street names be in order to be legible to a person with 20/50 vision from a distnace of 450 ..

  Discuss limitation and problem of extrapolating properties

DISCUSS THE LIMITATION AND PROBLEM OF EXTRAPOLATING MECHANICAL PROPERTIES MEASURED ON A SMALL ROCK SAMPLE TO FIELD SITUATIONS.

  What is the uniform deterministic arrival rate

what is the uniform deterministic arrival rate if the vehicle queue is cleared in 35 minutes after vehicles begin to arrive (in veh/min.)?

  Determine the maximum velocity that the skier will achieve

A person with a mass of 200kg wearing snow skis is gliding down a long slope at an angle of 20 degrees. Each ski is 200cm long and 5 cm wide. The pressure of the skis on the snow melts a thin layer of water so that a .1mm layer of water exists under ..

  Is the actual flow in the pipeline laminar or turbulent

Oil flows through the Trans-Alaska pipeline. Because oil is viscous, you might think that the flow is laminar. (a) What is the minimum flowrate (m3/s) for which the flow would likely be laminar.

  Determine the actual detention time observed in the field

Determine the actual detention time observed in the field of two circular settling tanks with depth 3.5 m that was designed to have an overflow rate not exceeding 60 m3/m2-day and a detention time of at least 2 hour.

  Determine the minimum diameter a steel wire can have

If the elastic limit of steel is 5.0 10^8 Pa, determine the minimum diameter a steel wire can have if it is to support a 69-kg circus performer without its elastic limit being exceeded.

  Find probability that the percent absorbed is more than 10

When a pesticide comes into contact with skin, a certain percentage of it is absorbed. The percentage of the pesticide that will be absorbed during a given tie period can be modeled with a lognormal distribution.

  What should the reading be at y to adjust collimation error

a level is setup midway between X and Y reads 5.572 ft on X and 4.946 ft. on Y. The level is setup very close to X and a reading of 4.666 ft. is taken on X. what should the reading be at Y to adjust any collimation error of the level

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd