Estimate the amount of water drained off in kg/h

Assignment Help Mechanical Engineering
Reference no: EM131027601

A dehumidifier brings in saturated wet air (100 percent relative humidity) at 30°C and 1 atm, through an inlet of 8-cm diameter and average velocity 3 m/s. After some of the water vapor condenses and is drained off at the bottom, the somewhat drier air leaves at approximately 30°C, 1 atm, and 50 percent relative humidity. For steady operation, estimate the amount of water drained off in kg/h. (This problem is idealized from a real dehumidifier.)

Reference no: EM131027601

Questions Cloud

Which is not one of the factors discussed in the given text : Divorce was rare in agricultural states because of a number of factors. Which of the following is not one of the factors discussed in the text?
How many cycles are required for each code snips : How many cycles are required for each code snips? Which is faster and by how much? What is the CPI for each code snip?
How do i show x+1 is primitive : How do I prove x^4+x^3+1 is an irreducible polynomial of degree 4 over Z mod?
How many second will it take to reach the ground level : Express the following statement as a formula with the value of the constant of proportionality determined with the given conditions: w varies directly as x and inversely as the square of y. If x=15 and y=5, then w=36.
Estimate the amount of water drained off in kg/h : A dehumidifier brings in saturated wet air (100 percent relative humidity) at 30°C and 1 atm, through an inlet of 8-cm diameter and average velocity 3 m/s. After some of the water vapor condenses and is drained off at the bottom, the somewhat drie..
Explanation of abina situation : To conclude, the author gave us a clear explanation of Abina's situation back in 1876 with passion, and a lot of sympathy for her
What is the wall thickness of the propane tank in mm : The welded handle and stand on the tank weigh 1 lbs (combined) and valve on the tank weighs 1.5 lbs and has an exit area of 1 cm^2 . What is the wall thickness of the propane tank in mm? what is the inner volume of the propane tank in mL and gallons..
How did diocletian and constantine deal with the political : How did Diocletian and Constantine deal with the political, social, and economic problems of the Roman Empire inthe third and fourth centuries AD?
Find a formula for the inverse of the function : Today you visited the R&D (Research and development) development of a pharmaceutical manufacturer. The people in this lab have to calculate the recommended dosage of the products they are developing. Medicine is expressed as a function of the conc..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd