Estimate extra cost per year due to increased use of blades

Assignment Help Mechanical Engineering
Reference no: EM13703812

Current airbag regulations specify that they must only pass a test designed to protect a 175 pound male who is not wearing a seatbelt. There is currently a discussion of lowering the explosive force by 30%, so that smaller-sized people (including women) would be less subject to injury due to the explosive force of the airbag; this would be adequate to protect seat belted individuals of around 175 pounds, but not enough for substantially heavier individuals or those not wearing seatbelts. (Note:  current airbags cost about $30. to manufacture).

Ethical question:  In one paragraph, discuss what you think of this proposed regulation, which is currently being discussed in the federal government.

1. Suppose that the US military is considering a new lifetime regulation on their helicopter rotor blades.  Instead of using them for 1000 hours (which leads to a likelihood of 5 failures per 10,000 blade sets), they are considering reducing the likelihood of a crash by replacing the blades after 500 hours, thus reducing the likelihood of a crash to 1 failure per 10,000 blade sets.  Assuming a fleet of 10,000 helicopters, and assuming the helicopters are flow for 1000 hours/year, and a cost per set of blades of $5000.

a) Estimate the extra cost per year due to the increased use of blades

b) Estimate the cost savings due to fewer crashes (assume a cost of $1million per helicopter, assume an average of two people in the helicopter, and remember that helicopter crashes are usually fatal).

c) Based on your calculations, what would you recommend? 

2) Determine the bonding type between the following types of atoms:

Al-Ni, Si-Ge, C-O, Fe-O, Ne-Ar

(Hint:  use the electro negativity table in Callister).

3) Explain why a Ti atom is larger than a Cu atom.

Reference no: EM13703812

Questions Cloud

Lbm block is pushed down a frictionless incline with a force : A 10 lbm block is pushed down a frictionless incline with a force of 5 lbf. the incline is 30 degrees relative to the horizontal. if the block starts from rest, what is its speed after it has been pushed 12 ft. Assume that gravity is 32.0 ft/ sec^2
What is torque required to stop it from spinning : A Cylinder of mass 20 lbs, radius 5in and height 10in is spinning about its axis of symmetry (central axis) at 200 rpms. What is torque required to stop it from spinning
Matrix with digits of the input number as diagonal elements : Write the MATLAB program which takes 8 digits number as input, then creates an 8x8 matrix with digits of the input number as diagonal elements and zeroes elsewhere using for loops. Then, execute the program using your student ID as input.
Determine the actual exit temperature for the compressor : A given mass flow rate (.17 kg/min) of an ideal gas flows through an adiabatic compressor operating at steady state. The compressor has an adiabatic efficiency of N(%) = 87.5. The gas has a molecular weight of MW = 28.5 (kg/kmol) and a specific heat ..
Estimate extra cost per year due to increased use of blades : Current airbag regulations specify that they must only pass a test designed to protect a 175 pound male who is not wearing a seatbelt. There is currently a discussion of lowering the explosive force by 30%, so that smaller-sized people (including wom..
Matlab program-average of digits of part using for loops : Write the MATLAB program to find the maximum, minimum and average of the digits of part (a) using for loops. Execute the program and list the output. Note that you are not allowed to use MATLAB commands max(x), min(x) and mean(x), except for checking..
What specific materials are used for solar cells : What specific materials are used for solar cells? What specific properties these materials process in order for the solar cells to the function properly?
Double-pipe heat exchanger : Double-pipe heat exchanger. This type of heat exchanger is composed of concentric pipes, with hot water flowing in the inner pipe while cold water flows in the annulus between the inner pipe wall and outer pipe wall.
Mass of oxygen gas in a container with a volume : What is the mass of oxygen gas in a container with a volume of 25 ft3, at a pressure of 14.7 psia and a temperature of 75oF?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd