Engineering calculations to justify component selection

Assignment Help Electrical Engineering
Reference no: EM131021723

Design three voltage divider networks to achieve the following design criteria.

With Vin = 10V, Vout should be within the range of 3.3 and 5V

With Vin = 5V and a load of 15kohm as a load connected from Vout to ground, the voltage across the load should be within the range of 2.5V and 3.3V

With Vin = 5V and a load of 1kohm, the current through the load should be less than 2mA.

Include the following:

Engineering calculations to justify component selection.

Screenshot of the circuit constructed with MultiSIM (or equivalent circuit simulator)

Screenshot of the circuit simulation running and the measurements of the required voltages and currents shown on a virtual digital multimeter from MultiSIM as shown in this week's lecture.

Reference no: EM131021723

Questions Cloud

What is the marginal revenue of the eleventh unit : When the firm cuts the price from $5.00 to $4.75 to sell the eleventh unit, what area in the graph denotes the output effect, and what is the dollar value of the output effect? What area in the graph denotes the price effect, and what is the dolla..
Discuss the functions of the joint commission : Discuss the functions of the Joint Commission. Define the categories of accreditation. Discuss the National Committee for Quality Assurance (NCQA). How does the NCQA impact health information systems?
Is possible for marginal revenue negative for firm selling : Is it possible for marginal revenue to be negative for a firm selling in a perfectly competitive market? Is it possible for marginal revenue to be negative for a firm selling in a monopolistically competitive market? Briefly explain.
Discuss the five major components of hipaas privacy rule : Discuss the five major components of HIPAA's privacy rule. Discuss three HIPAA-covered entities. Discuss how the HITECH Act and HIPAA work together to ensure patient security. How do they differ?
Engineering calculations to justify component selection : Screenshot of the circuit simulation running and the measurements of the required voltages and currents shown on a virtual digital multimeter from MultiSIM as shown in this week's lecture.
What would you identify in job analysis within organization : What would you identify in a job analysis within an organization, which are the most important factors that would help the supervisors do his or her jobs?
Why in announcing new video game console would microsoft : The article goes on to say that not until nearly half way through the presentation did the Microsoft spokesman mention the new games the console could play. Why in announcing a new video game console would Microsoft focus its presentation on feat..
Demonstrates the potential interaction of the arduino board : A block diagram that shows the 8-bit AVR along with the data and address busses. Use a graphics package such as Fritzing or equivalent.
Does your answer depend on the rate of return : Once McDonald's has made its decision about the size of the store it will build, Burger King will decide whether to enter this market. Use the following decision tree to decide the optimal strategy for each company. Does your answer depend on the ..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How much electricity is needed for single rotation of motor

What are the types of motor Which motor is user in Car Engines which is the most efficient motor How much electricity is needed for single rotation of general motor

  Power factor correction example

Problem: A load has 10 A current at a lagging power factor of 50%. Voltage is 120 V, and frequency is 60Hz. What size capacitor must be used to bring power factor to 90%?

  Specify truth table for rom together with line converters

The 32 X 6 ROM together with the 2^0 line converts a 6-bit binary number to its corresponding 2-digit BCD number. For example, binary 100001 converts to BCD 011 0011 (decimal 33). Specify the truth table for the ROM.

  What will be the power factor when the inductor voltage

What will be the power factor when the resistor voltage is 9 V at an angle of 30 degrees, and the capacitor voltage is 3 V at an angle of - 60 degrees in a RC series circuit. Also, what will be the power factor when the inductor voltage is 9 V.

  Find the output frequency spectrum-pep and power output

The frequencies Of the signal are 600 Hz and 1.6 kHz with the carrier at 90 kHz. If the rms voltage levels for the 2-tones is 3.22 volts and the load resistor is 71 Ohms, find the output frequency spectrum, PEP, and the average power output.

  Calculate magnitude of voltage v3 across the third impedance

a.Sketch the circuit diagram, the impedance diagram and the phasor diagram; take the supply voltage V as the reference phasor. b. Calculate the magnitude of the voltage V2 across the second impedance. c. Calculate the magnitude of the voltage V3 acro..

  Calculate the magnitude of electric field vector at point a

Two point charges q1 = 2.0 C and q2 = 1.0 are fixed in a plane at the positions given by the Cartesian coordinates shown in the figure at right. Consider that they are in a vacuum, where ko = 9.0 × 109 N.m2/C2.

  Determine what is the probability of false alarm

A spread-spectrum acquisition system uses a serial search scheme.The synchroniser integrates the squarer output for interval of 0.1s and the synchroniser output is sampled at intervals of 0.05s . The probability of false alarm is 0.064255 .

  What are the advantages of parallel circuits

What are the Advantages of Parallel Circuits connection over Serie Circuit Connection ? Why Parallel Connection is Mostly Preferred over Series Connection?

  Calculate the diode current for the forward bias

A pn-junction is uniformly doped and has dopant concentration of NA = 4 x10^16 cm^-3 in the pregion at 300K. At zero bias, 20% of the total space charge region (W) is extended in the pregion. Calculate Vbi, ND, W, xn and xp.

  Compute 25 seconds of the discrete-time signal x

x[n]=cos(n*7pi/16)+cos(n*9*pi/16) a)Find the FS coefficients of x[n]. b)Obtain the DTFT of x[n] using the  coefficients. c) Use Matlab, compute 25 seconds of the discrete-time signal x[n] using an appropiate sample period Ts.

  What is the modulation used to transmit hdtv signals

What is the modulation used to transmit HDTV signals over the air in US terrestrial broadcasting? What is the transmitted bit rate and the compression method?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd