Engine assuming gallon gasoline produces

Assignment Help Mechanical Engineering
Reference no: EM13719027

As a 75 slug car travels along a horizontal, 3200 ft section of road, it changes speed from 5 mph to 60 mph. During this acceleration, how efficient is the car's engine assuming 1 gallon gasoline produces 120 MJ of energy when completely combusted in air?

Reference no: EM13719027

Questions Cloud

Explain about transaction and transform mapping : explain about transaction and transform mapping
Width from plate for values of the critical reynolds number : Consider atmospheric air at 25 degrees Celsius and a velocity at 25 m/s flowing over both sides of a 1  eter long flat plate that is maintained at 125 degrees Celsius. Determine the rate of heat transfer per unit width from the plate for values of th..
Explain how you define the times of sunrise and sunset : Explain how you define the nodes xk that represent the dates above - Define a global interpolating polynomial Pr that passes through all data points given for the time of sunrise.
Diameter impeller of a radial-flow water pump rotates : A 400-mm-diameter impeller of a radial-flow water pump rotates at 120rad/s and has a discharge of 0.5m3/s. Determine the discharge for a similar pump that has an impeller diameter of 100mm and operates at 90rad/s.
Engine assuming gallon gasoline produces : As a 75 slug car travels along a horizontal, 3200 ft section of road, it changes speed from 5 mph to 60 mph. During this acceleration, how efficient is the car's engine assuming 1 gallon gasoline produces 120 MJ of energy when completely combusted in..
Temperature of the refrigerant exiting the compressor : Refrigerant R134a is compressed under steady conditions from a saturated vapour at 100 kPa to 500 kPa. The compressor’s isentropic efficiency is 85%. Heat losses from the compressor can be ignored, as can kinetic energy and potential energy effects.
Heat exchanger required to achieve the desired heating : A counter-flow double pipe heat exchanger is heat water from 20 degrees Celsius to 80 degrees Celsius at the rate of 1.2 kg/s. The heating is to be accomplished by geothermal water available at 160 degrees Celsius at a mass flow rate of 2 kg/s.
Counter flow double pipe heat exchanger is to heat water : A counter flow double pipe heat exchanger is to heat water from 20 degrees Celsius to 80 degrees Celsius at the rate of 1.2 kg/s. The heating is to be accomplished by geothermal water available at 160 degrees Celsius at a mass flow rate of 2 kg/s.
Double-tube counter flow heat exchanger : Hot oil is to be cooled in a double-tube counter flow heat exchanger. The copper inner tubes have a diameter of 2 cm and negligible thickness. The inner diameter of the outer tube (the shell) is 3 cm. Water flows through the tube at a rate of 0.5 kg/..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd