Energy when completely combusted in air

Assignment Help Mechanical Engineering
Reference no: EM13718981

As a 75 slug car travels along a horizontal, 3200 ft section of road, it changes speed from 5 mph to 60 mph. During this acceleration, the car gets an average MPG of 15 MPG. How efficient is the car’s engine during the acceleration assuming 1 gallon of gasoline produces 120 MJ of energy when completely combusted in air?

Reference no: EM13718981

Questions Cloud

Saturated liquid entering and saturated vapor exiting : A Carnot power cycle operates at steady state with water as the working fluid. The boiler pressure is 200lbf/in^2, with saturated liquid entering and saturated vapor exiting. The condenser pressure is 20lbf/in^2.
Air flows with heat exchanger : Air at 600k flows with 3 kg/s into a heat exchanger and out at 100 C. How much (kg/s) water coming in at 100 KPA, 20 C can the air heat to the boiling point?
Clockwise without slipping on the fixed horizontal surface : At the instant shown, the rigid body OA rolls counter clockwise without slipping on the fixed horizontal surface, and point O has a velocity 2 m/s to the left and an acceleration of 1 m/s2 to the right. Point O is at the center of the semi-circle reg..
Cauldron of boiling liquid with a pulley system : A witch lifts her cauldron of boiling liquid with a pulley system. Once the cauldron is lifted, liquid issues from two identical holes of cross-sectional area 2,000 mm2 (each) with a velocity of 30 m/s. The liquid sprays 30o below the horizontal.
Energy when completely combusted in air : As a 75 slug car travels along a horizontal, 3200 ft section of road, it changes speed from 5 mph to 60 mph. During this acceleration, the car gets an average MPG of 15 MPG. How efficient is the car’s engine during the acceleration assuming 1 gallon ..
Calculate starin in axial and transverse direction : A 10-ft long rectangular ASTM Grade 50 steel plate 1-in by 12-in cross section is used as a hanger and is subjected to a tensile load of 240,000 lb . the modulus of elasticity for steel is 30,000,000 psi and the poison ratio is 0.25
Compute the stress-strain and total elongation : A 24 in long bar with a cross sectional area of 1.0 in^2 is subjected to an axial tensile load of 10,000 lb. compute the stress, strain and the total elongation if the bar material is :
Determine the air velocity at the exit when inlet velocity : The exhaust nozzle of a jet engine expands air at 388 kPa and 174 C adiabatically to 95 kPa. Determine the air velocity at the exit when the inlet velocity is low and the nozzle isentropic efficiency is 96 percent.
Suspended in a room filled with saturated steam : A 1.2-cm-diameter silver sphere initially at 25°C is suspended in a room filled with saturated steam at 100°C. Using the lumped system analysis, determine how long it will take for the temperature of the ball to rise to 50°C. Also, determine the amou..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the work done by the friction on the crate as the

a crate with weight w165 lb and mass center g is placed on a slide and released from rest as shown. the lower part of

  Calculate delta velocity required to change the inclination

Calculate the delta velocity required to change the inclination of a circular orbit at 32,000 km altitude from a 28.5 degree inclination to an inclination of 45 degrees. Compute the propellant used if the satellite weighs 1200 lbs after the manoeuvre..

  Determine power developed by the turbine

Air enters a gas turbine with a velocity of 165m/s and a specific enthalphy of 2800KJ/kg and leaves with a velocity of 135m/s and specific enthalpy of 2175KJ/kg. The heat lost to the surrounding turbine is 32.5KJ/kg. Determine power developed by the ..

  Water flows in a 5-m-wide channel with a speed of 2 ms and

water flows in a 5-m-wide channel with a speed of 2 ms and a depth of 1m. the channel bottom slopes at a rate of 1 m

  River has a cross-section that is approximately a rectangle

A river has a cross-section that is approximately a rectangle 10-ft deep and 50-feet wide. The average velocity is 1 ft/s. How many gallons per minute pass a given point? What is the average velocity (assuming steady flow) at a point downstream, wher..

  Calculate the pressure difference between inside and outside

Tall buildings can develop a significant difference in pressure between the inside and the outside of the building. Air lock entrances are used at the ground level so the pressure at the ground floor is not the same as atmospheric pressure. Assume th..

  Determine the power kw for the compressor if the inlet

air enters an adiabatic compressor at 197 kpa and 316 k and exits at a temperature of 508 k. determine the power kw for

  What is a typical pearlite structure

Using the iron-Carbon equilibrium phase diagram, please describe the lines of transformation to austenite during heating with carbon content

  You are designing a remote-area power supply based on a

you are designing a remote-area power supply based on a miniature wind turbine that is 20 efficient. meteorological

  The initial interference required to produce

A laminated steel (E=200 GPa and nu=0.3) cylinder consists of a jacket with an inside diameter of 250mm and an outside diameter of 300mm shrunk onto a tube with an inside diameter of 150mm. The initial shrinkage pressure is 28MPa.

  When designing a front end loader what considerations must

when designing a front end loader what considerations must you make in the machine how it might be used and the type of

  Design an automatic speed control for an automobile

We wish to design an automatic speed control for an automobile. Assuming that pure integral control (that is, no proportional term) is advantageous; select the feedback gain so that the roots have critical damping (? = 1).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd