Energy conservation and availability balance equation

Assignment Help Mechanical Engineering
Reference no: EM13713186

Water vapor at 300 C, 35 bars (state 1) expands to 5.0 bars (state 2) using an adiabatic throttling valve. The ambient is at T = 25 C, 1 bar.

a. Simplify the energy conservation and availability balance equation for the current problem.

b. Calculate the exergy in kJ/kg at states 1 and 2.

c. Estimate the optimum work and irreversibility in KW if the mass flow is 20 kg/sec.

Reference no: EM13713186

Questions Cloud

What is the angular velocity of the bicycle : A bicyclist starts at rest at the top of a 50.3m long hill. After a small push, he coasts speeding up with an acceleration of 3.43m/s2 due to the slope of the hill. What is the angular velocity of the bicycle tires at the bottom of the hill.
Electrical work is employed to heat : Electrical work is employed to heat 2kg of water from 298.15 K to 373.15 K. Determine the electrical work required, and the minimum work required (e.g., by using a heat pump instead).
Write a summary of the book born to buy : You need to write a summary of the book born to buy.
The crankshaft in a given automobile rotates : The crankshaft in a given automobile rotates, on average, at 2500 revolutions per minute for a period of 2 h per day. How long would it take before the crankshaft has been subjected to 10^8 load cycles?
Energy conservation and availability balance equation : Water vapor at 300 C, 35 bars (state 1) expands to 5.0 bars (state 2) using an adiabatic throttling valve. The ambient is at T = 25 C, 1 bar. Simplify the energy conservation and availability balance equation for the current problem. Calculate the ex..
What is the internal resistance of the battery : A battery has an emf of 15.0 V. The terminal voltage of the battery is 13.4 V when it is delivering 16.0 W of power to an external load resistor R. What is the internal resistance of the battery.
Landing gear on a commercial aircraft experiences : The landing gear on a commercial aircraft experiences an impulse load upon landing. Assuming seven such landings per day on average, how long would it take before the landing gear has been subjected to 108 load cycles? (Answer in years)
Same mass is added through both inlets : An initially empty, well insulated, rigid tank with a volume of 2 m^3 is fitted with a mixing device. The tank has two inlets and zero outlets. One inlet is water at 1.07 MPa and 630ºC while the other is saturated liquid water. Both enter the tank sl..
Persuasion persuasive speech outline : Public speaking and persuasion Persuasive speech outline -

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd