Reference no: EM13277213
1. You will be designing a "Full Wave Bridge Rectifier" using four 1N4148 diodes and other linear components (R, L, C). (Note, use 2k? or above for the load resistor)
2. You will be using sinusoidal AC voltage source from the function generator as the input to your circuit. Use below parameters for the AC voltage source from the function generator.
Vp-p = +/-8V
Freq = 1kHz
Wave = sinusoidal (sine wave)
3. The target of this design is to achieve "DC voltage output" from the "AC voltage input" by using the rectifier and appropriate filters. You need to add appropriate "filter circuit" at the load to eliminate (reduce) the ripples caused by AC voltage input. DO "NOT" ADD ZENER DIODE VOLTAGE REGULATOR AT THE END.
4. Analyze your circuit. Explicitly state all applicable status, assumptions, and theorems (laws) that have been used in your solution.
5. Perform PSPICE simulation for your circuit to confirm your analysis. Plot (and submit) input voltage, output voltage, and circuit schematics. Try to vary the filter portion (R, L, C) of your circuit and plot (and submit) output voltages.
6. Perform experiments using your circuit design. Using your digital scope, plot (and submit) input voltage and output voltage from your circuit design. Try to vary the filter portion (R, L, C) of your circuit and plot (and submit) output voltages.
7. Be sure to submit ALL your "intermediate steps" (output results for both PSPICE simulations and experiments).
8. Discuss your results in detail with your own words. Even though you have worked in groups, you will need to write your own discussion by yourself.
|
Explain the initial temperature of the ethylene glycol
: A 23.7-g sample of ethylene glycol, a car radiator coolant, loses 906 J of heat. What was the initial temperature of the ethylene glycol if the final temperature is 32.5 degrees Celsius (c of ethylene glycol=2.42 J/g*K)
|
|
Calculate approximate number of primary and secondary turns
: A 6600V/230V, 50Hz single phase core type transformer has a core section 25cmX25cm. Calculate the approximate number of primary and secondary turns if the flux density in the core should not exceed 1.1Wb/m2.
|
|
How to calculate q when 15.8 g of ice is cooled
: Calculate q when 15.8 g of ice is cooled from -22.4 degrees Celsius to -71.0 degrees Celsius (C ice = 2.087 J/g*K)
|
|
Determine the water speed in each hose
: Three fire hoses are connected to a fire hydrant. Each hose has a radius of 0.017 m. Find the water speed in each hose
|
|
Eliminate or reduce the ripples caused by ac voltage input
: Perform experiments using your circuit design. Using your digital scope, plot (and submit) input voltage and output voltage from your circuit design. Try to vary the filter portion (R, L, C) of your circuit and plot (and submit) output voltages.
|
|
Explain what volume of hcl needs to be added
: Consider titrating 15.0ml of a .245M solution of hydazine, H2NNH2, with a .453M HCl solution. The Kb value for hydrazine is 1.3x10^-6. What volume of HCl needs to be added to the solution in oder to have a bffer system with the maximum capacity fo..
|
|
What is the effect size and what does it mean
: Perform post hoc comparisons if necessary and what conclusions can be drawn from the F- ratio and the post hoc comparisons?
|
|
What minimum force must be applied to the small piston
: A hydraulic lift in a garage has two pistons: a small one of cross-sectional area 3.60cm2, If this lift is designed to raise a 3300-kg car, what minimum force must be applied to the small piston
|
|
Choose one of the open source web content management systems
: Choose one of the open source Web content management systems such as WordPress, Joomla, or Drupal or another of your own choosing and prepare an evaluation chart. Which system would you choose and why?
|