Elevator to the third floor of a parking garage

Assignment Help Mechanical Engineering
Reference no: EM13704700

A car is to be hoisted by elevator to the third floor of a parking garage, which is 36 ft above the ground. If the elevator can accelerate at 0.7 ft/s2, decelerate at 0.2 ft/s2, and reach a maximum speed of 8 ft/s, determine the shortest time to make the lift, starting from rest and ending at rest. Express your answer using three significant figures and include the appropriate units.

Reference no: EM13704700

Questions Cloud

A fan accelerates air : A fan accelerates air (at atmospheric pressure and 300K) from a rest to 5m/s. The fan mass flow rate of air is 1.2 kg/s. What is the minimum amount of power this fan must consume to operate under these conditions?
What is the likely response from the board members : What are the issues that you will take into account and what is the likely response from the board members?
Compute the first energy level : Compute the first energy level (in eV) for a particle trapped in a 0.1 nm region. Assume the mass of the particle is equal to 0.511 MeV/c^2
Determine the atomic packing factor : Determine the atomic packing factor (APF) of the simple hexagonal crystal structure assuming the lattice parameter a is equal to 2R and the lattice parameter c is equal to 1.5 a. The Bravais lattice is shown below. Assume one atom on each lattice poi..
Elevator to the third floor of a parking garage : A car is to be hoisted by elevator to the third floor of a parking garage, which is 36 ft above the ground. If the elevator can accelerate at 0.7 ft/s2, decelerate at 0.2 ft/s2, and reach a maximum speed of 8 ft/s, determine the shortest time to make..
Volatility of demand on your service delivery system : Assume that the volatility of demand on your service delivery system is much higher than that on your manufacturing production system. Your management has indicated that the anticipated inventory storage will smooth the demand in manufacturing,..
Needing a tutor to help writing punitive damages promote : Needing a tutor to help writing punitive damages promote injustice to society and that tort reform is needed. Needing a cover page, table of contents, introduction, highlight of punitive damages and its injustice to the society, case analysis, ..
Velocity at which the skydiver will fall toward the earth : A skydiver bails out of an airplane at 2000m above mean sea level but cannot make his parachute work at first. The skydiver weighs 70 kg and is 1.7m tall. Determined the approximate velocity at which the skydiver will fall toward the earth. Base your..
Find the publisher breakeven output and the output : Find the publisher's breakeven output and the output that would lead to a total profit of $60,000

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd