User Account

All Pages

Dry air enters an industrial dryer with a pressure of 101

Assignment Help Mechanical Engineering
Reference no: EM13628901

Dry air enters an industrial dryer with a pressure of 101 kPa, a temperature of 250*C, and a mass flow rate of 2.6kg/hr through a duct with a cross-sectional area of 0.85m^2. A wet material is placed inside the dryer, and its rate of drying is 5.5g/min. Determine the mass flow rate of gases leaving the dryer and the average velocity of air entering the dryer, assuming steady operation.

Reference no: EM13628901

Questions Cloud

In a certain city 46 of the people adults classify : in a certain city 46 of the people adults classify themselves as independent 30 classify themselves as liberals and 24
If the exit pressure is 200 kpa and the inlet volumetric : an air compressor is powered by a 2hp motor assume this is all input to the compressor. the inlet pressure and
Two site are being considered for wind power generation in : two site are being considered for wind power generation. in the first site the wind blows steadily at 7 ms for 3000
The exit temperature of the water is 25oc then what is the : an adiabatic heat exchanger has 0.3 kgs of water passing through one flow path. the inlet temperature and pressure are
Dry air enters an industrial dryer with a pressure of 101 : dry air enters an industrial dryer with a pressure of 101 kpa a temperature of 250c and a mass flow rate of 2.6kghr
A engineer is going to redesign an ejection seat for an : a engineer is going to redesign an ejection seat for an airplane. the seat was designed for pilots weighing between 120
Air enters and air compressor at a steady volume flow rate : air enters and air compressor at a steady volume flow rate of 45 m3min. the air pressure increases from 100 to 700 kpa
A psychologist would like to evaluate the relationship : a psychologist would like to evaluate the relationship between academic ability as measured by the act and academic
A closed system consisting of 145 lb of air undergoes a : a closed system consisting of 14.5 lb of air undergoes a polytropic process from p1 80 lbfin2 v1 4 ft3lb to a final

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The ice cap at the north pole may be 1000 m think with a

the ice cap at the north pole may be 1000 m think with a density of 920 kgm3. find the pressure at the bottom and the

  In a chain link fencing machine if we are using 2mm gi wire

in a chain link fencing machine if we are using 2mm gi wire at the feed of 10mm per second through a self centering

  Determine the irreversible power loss within the dam and

the hoover dam has a capacity to produce 2080 mw of electrical power. the difference in height between the surface of

  Finding the time interval for the motorcyclist to reach a

finding the time interval for the motorcyclist to reach a given acceleration if the motorcyclist starts from rest

  Estimate time necessary to achieve the same concentration

Estimate the time necessary to achieve the same concentration at a 5.3-mm position for an identical steel and at the same carburizing temperature.

  A pipeline is to be supported above ground on horizontal

a pipeline is to be supported above ground on horizontal beams 14ft long. consider each beam to be simply supported at

  Calculate the final temperature in the small cylinder

If the filling is done rapidly, calculate the final temperature in the small cylinder, (a) assume that oxygen is an ideal gas with Cv= 5R/2 and (b) using accurate thermodynamic data for oxygen.

  The final pressure is 14 mpa determine the work and the

a pistoncylinder arrangement is filled with helium gas. the gas is compressed with a polytropic process with nk. the

  To the nearest 01 what is the safety factor if the bracket

a cantilevered beam bracket of uniform cross section extends 12 inches from the wall and supports 100 pounds of load at

  Determine the turbocharger pressure ratio required to

intake air to turbocharger for internal combustion engine is 100kpa at 300k. determine the turbocharger pressure ratio

  Using both graphical and analytical methods in assessing

the following linear failure envelopes for a rock mass are givenintact rockfriction angle 350cohesion 900 psitension

  Explain what is the tangential force

A spur gear has 48 teeth with a diametral pitch of 8 and a pressure angle of 20 deg. The face width is 0.75 inches. If the gear is transmitting 25 HP at 250 rpm

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd