Drip irrigation problem

Assignment Help Mechanical Engineering
Reference no: EM13708158

Drip irrigation is a means of getting water directly to growing plants with very little waste. One method uses a large-diameter polyethylene "mother" tube (10-15 mm i.d.) from which lead many small diameter polyethylene feeder tubes, called drippers, which go directly to the individual plants. What length of 0.5mm tubing will give a flow rate of 20 degrees C water of 6L/day if the pressure is 2 bar in the mother tube, and 1 bar in the surroundings?

Referring to the above problem, what diameter and length of dripper should we use if we want a flow rate of 4 L/h to each plant, and if the desired dripper lenght is to be somewhere between 0.5 and 1.5 m?

Data: the temperature is 20 degrees C; mother tube pressure 200kPA; ambient pressure= 100kPa; drippers are manufactured in 3 diameters: 0.5mm, 1.0mm, and 1.5mm.

Reference no: EM13708158

Questions Cloud

Determine the axial stress required to induce this strain : An aluminium bar is subjected to uniaxial tensile loading. If the lateral strain (perpendicular to the load direction) is measured to be -0.00025, determine the axial stress required to induce this strain (round to the nearest ksi).
Maximum normal stress and the maximum shear stress : A thin walled tube with closed ends has an inside radius of 80mm and a wall thickness of 6 mm. It is subjected to an internal pressure of 20 MPa, a torque of 60 kN*m, and an axial compressive force of 200 kN. Determine the maximum normal stress and t..
Determine the volumetric flow rates at the inlet and exit : Refrigerant 22 enters an insulated compressor operating at steady state as saturated vapor at - 16 C with a mass flow rate of 1.5 kg/s. Refrigerant exits at 7 bar, 70 C. Changes in KE and PE from inlet to exit can be ignored. Determine: (a) the volum..
Calculate displacement-velocity-acceleration for assembly : A certain piston cylinder assembly has a stroke of 85mm, a connection rod length of 130 mm and a piston pin offset of 2mm. Calculate the displacement, velocity and acceleration of the assembly operating at 2200 RPM. If the same configuration is used ..
Drip irrigation problem : Drip irrigation is a means of getting water directly to growing plants with very little waste. One method uses a large-diameter polyethylene "mother" tube (10-15 mm i.d.) from which lead many small diameter polyethylene feeder tubes, called drippers,..
Block of copper at at initial temperature : A 25-kg block of copper at at initial temperature of 150 C equilibrates with 0.79 kg of liquid water at an initial temperature of 20 C in an insulated tank. If the average specific heat of copper can be taken to be 0.395 kJ/kg.K, determine the final ..
The raw material price and consumable price : Within the last month, the raw material price and consumable price combined has increased by 5.5%. If the throughput was 5 parts/hour estimates the future throughput that has to take place in order to maintain a constant production cost. Consider the..
Compressor is employed to compress gas : A compressor is employed to compress gas flowing steadily through it. The gas enters the compressor at a temperature of 16°C, a pressure of 100 kPa, and with an enthalpy of 391.2 kJ/kg. The gas leaves the compressor at a temperature of 245°C, a pre..
Buoyant device used for measuring specific weight of liquid : A hydrometer is a buoyant device used for measuring the specific weight of a liquid. A weighed glass bulb floats below the surface with a graduated stem extending above the surface. The position of the fluid level on the steam corresponds to the spec..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd