User Account

All Pages

Draw the piezo block and fibre optics cable

Assignment Help Mechanical Engineering
Reference no: EM13941503

Drawing a simple diagram uisng Ansys software

Using Ansys draw the piezo block and fibre optics cable attached to the top of thepiezo block. After drawing, mesh the piezo block and the fibre optics.

Choose suitable materials for the piezoelectric material block and fibre optics from Ansys. i.e. for the fibre optics cable, you may choose any glass. Show screen shots of Ansys on your development pasted on a word document.

The fibre optics cable must be placed centrally

1900_Fibre optics cable.png

Dimensions of piezo block Length 7cm, width = 1.5 cm, height 1cm

Fibre optics diameter 0.5 cm , Length 8cm.

Example of a MESHED piezo block ( you may choose to mesh it more i.e. more meshed sub-blocks, please mesh the attached fibre too

74_Fibre optics cable1.png

Reference no: EM13941503

Questions Cloud

Use of width and height attributes in an element : Which of the following will occur if you do not use the width and height attributes in an element?
Firms risk without increasing current borrowing costs : The conflict resulting from a manager's desire to increase the firm's risk without increasing current borrowing costs and lenders' desire to limit lending is one effect of the _______ problem.
What is the value of equity for each firm : Skim Milk and Part Whole Milk are identical firms except that Skim is more leveraged than Part Whole. The probability of a recession is equal to the probability of an expansion. If recession occurs, each Firm will have EBIT of $0.5 million next year...
Writing a research paper based on mutual funds : Writing a research paper based on mutual funds. We had to pick an investment topic and I chose to write about mutual funds and I am having a hard time with my introduction to the paper. I want to go over mutual funds and the investment policies assoc..
Draw the piezo block and fibre optics cable : Using Ansys draw the piezo block and fibre optics cable attached to the top of thepiezo block. After drawing, mesh the piezo block and the fibre optics.
Comprehensive analysis of existing offerings on market : A comprehensive analysis of existing and similar offerings on the market already including a feature and parametric analysis indicating how your proposal fits into the existing scenario.
What is the worst-case NPV : An investment under consideration has a payback of eight years and a cost of $868,000. Assume the cash flows are conventional. If the required return is 10 percent, what is the worst-case NPV?
Corporate social responsibility and stakeholder engagement : Analyse their CSR strategy based on the tools (stakeholder frameworks, materiality analysis, and possibly other tools from Epstein's book) Based on this analysis, suggest some recommendations for Google at this stage.
Does increase number of immigration violations lead : Does the increase in the number of immigration violations lead to increase in crime? Identify the sources of existing data that was discovered for the above research question.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If the power output of the turbine is 2 mw determine a the

steam enters an adiabatic turbine steadily at 3 mpa and 400 degree c and leaves at 50 kpa and 100 degree c. if the

  Below the 5cm thick asphault with an average conductivity

the sun shines on a 500m2 road surface at 50c. below the 5cm thick asphault with an average conductivity of 0.1 wmk is

  Compare annual profit when the plant is operating at 90 of

a planet operation has fixed costs of 2000000 per year and its output capacity is 100000 electrical appliances per

  A dragster comes off the start line with an acceleration of

a dragster comes off the start line with an acceleration of 4 ms2. the acceleration increases uniformly from 4 ms2 to

  Determine the change in flow exergy of the refrigerant

0.75 kg of Refrigerant 134-a is compressed in a compressor from 160 kPa and -10°C to 1.2 Mpa and 50°C, steadily. Determine the change in flow exergy of the refrigerant during this process, if the environment is at 100 kPa and 25°C.

  A simple u-tube manometer is installed across an orifice

a simple u-tube manometer is installed across an orifice meter. the manometer is filled with mercuryspecific gravity

  Neglecting kinetic energy changes

Helium is to be compressed from 120 kpa and 340 K to 700 kPa and 460 K. A heat loss of 20 kJ/kg occurs during the compression process. Neglecting kinetic energy changes, determine the power input required for a mass flow rate of 89 kg/min.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  Etermine the force applied by the ram

A cube of 2" dimensions is placed in a square hole (also of 2" dimensions) that is 1.998" deep. The hole was cut out of a rigid material. (The top of the cube protrudes .002" above the surface). If a flat rigid plate is placed on top of the cube and ..

  Radiation from sun is absorbed at the plate surface at the

the flat plate 1 m in length and 1 m in width is placed parallel to the air stream at 27ordmc 1 atm. the air free

  The heat capacitance of various gases

The heat capacitance of various gases

  Assume the regriderator works in a carnot cycle between -10

a refridgerator should remove 500 kj from some food. assume the regriderator works in a carnot cycle between -10 and 45

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd