Draw the cross sections and compute ve

Assignment Help Civil Engineering
Reference no: EM13561525

1.Draw the cross sections and compute Ve (average end area volume) using the following data: two level sections 100 ft apart with center heights 4.2 and 5.6 ft in fill, base width 30ft, side slopes 1-1/2:1.

2.The pressure inside a 4cm hose is 700 kPa. If water exits through a 2 cm diameter nozzle, what velocity m/s, can be expected inside the hose?

Reference no: EM13561525

Questions Cloud

Describe and evaluate a company nike pricing and retail : Describe and evaluate a company Nike's pricing and retail strategy
Imagine you have been selected to conduct a recruiting : Imagine you have been selected to conduct a recruiting
A new section of richmod highway is being designed : A new section of richmod highway is being designed as a six-lane facility (three in each direction) with a two-way, left-turn lane. Determine the peak hour LOS.
Each project passes through different processe : Each project passes through different processe
Draw the cross sections and compute ve : The pressure inside a 4cm hose is 700 kPa. If water exits through a 2 cm diameter nozzle, what velocity m/s, can be expected inside the hose?
High school graduate required to spend two years in military : THE TOPIC SHOULD READ " High school graduate should be required to spend two years in military and then receive a free college education"
Evaluated the marketing environment : you have evaluated the marketing environment and established some marketing goals for MM
Develop a model for the relationshp for the rate of the grow : A gas bubble is formed at the tip of a small tube which is completely immersed in a large body of liquid. The bubble remains in contact with the open end of the tube in a way that allows us to control the pressure P inside the bubble.
What cycle length would you use : You have been asked to design a simultaneous traffic signal system for six intersections on a suburban arterial. The distances between consecutive intersections are:

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the resulting solids concentration

Raw primary sludge at a solids concentration of 4% is mixed with waste activated sludge at a solids concentration of 0.5%. The flows are 20 and 24 gal/min, respectively. What is the resulting solids concentration

  Determine for the crest and sag vertical curves required

Two level sections of an east-west highway (G = 0) are to be connected. Currently, the two sections of highway are separated by a 4000-ft (horizontal distance), 2 % grade.

  Determine what is the turbidity of the original sample

A wastewater sample was diluted by turbidity free water; 5ml was diluted to 250 ml. Turbidity of the diluted sample was 2.3 NTU, what is the turbidity of the original sample

  Calculate the final pressure temperature when the nitrogen

Calculate the final pressure, temperature when the nitrogen isreduced to that volume. What is the modulus of elssticity at thebeginning and end of the compression. k=1.4

  Calculate the volume flow rate into the compressor

A 12kw (shaft output) motor is available to run a non-cooled compresor for helium. The pressure is to be increaded from 80 kPa to 120 kPa. If the compressor is 70% efficent, calculate the volume flow rate into the compressor.

  Determine bulk density and the degree of saturation

A cylindrical sample of soil 39 mm in diameter and 77 mm long weighed 180 g. The sample is not fully saturated and its moisture content was found to be 27.0%. Assume rS = 2.70 Mg/m3. Determine: a. the bulk density, r b. the dry density, rd c. the d..

  Calculate void ratio and degree of saturation of the soil

The value of Gs is 2.70. Calculate the void ratio and degree of saturation of the soil. What would be the values of density and water content if the soil were fully saturated at the same void ratio

  Determine the moment about the pin due to the force

1.For an SO2 emission rate of 22,000 kg/day and an exhaust gas flow rate of 5.0 million m^3/hour(after the scrubber) measured at 150 C and 1atm pressure, calculate the concentration of SO2 in the exhaust gases(ppm).

  Determine the capitalized cost of the project to construct

This project is expected to have a first cost of $2,000,000 and an annual maintenance cost of $50,000. In addition, major repairs costing $250,000 will be required after 25 years and each 15 years thereafter.

  Calculate the absolute pressure head and the gage pressure

The pressure in the steam condenser of a nuclear power plant is 1 psia. Calculate the absolute pressure head, the gage pressure, the gage pressure head, the vacuum pressure, and the vacuum pressure head under standard conditions.

  Determine the estimated cost of a similar process unit

From historical cost records, the capacity ratio exponent of a process unit is 0.5. Use the capacity ratios raised to an exponent method to determine the estimated cost of a similar process unit with a capacity of 310 ft3/hr.

  What flow rate of fresh water (in m3/s) must they use to red

mg/L of salt. The new owners propose to flush the pond into their discharge pipe leading to the Atlantic Ocean, which has a salt concentration above 30,000 mg/L.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd