User Account

All Pages

Draw in third angle projection

Assignment Help Mechanical Engineering
Reference no: EM13295501

Question 1

A pictorial view of a bearing pedestal is given in Figure I.

Draw. in Third Angle Projection. the following orthogonal views:

a Front View from A

ii. a Sectional Side View from 8 on a vertical cutting plane through the centre line of the bearing journals

III. a Top View.

Fully dirrension and provide a titk block. Use a scale of I:I and plot on an A3 sheet.

604_pictorial view of a bearing pedestal.png

Reference no: EM13295501

Questions Cloud

What is the density of the beer : The gauge pressure at the bottom of a pint of beer, at a depth of 14.6 cm, is 1450 Pa. What is the density of the beer
Explain the possible effect on results errors : Describe/explain the possible effect on your results of the following experimental errors or variations
Calculate the present value of the generated cash flows : Enter rounded answer as directed, but do not use the rounded numbers in intermediate calculations.Round your answer to 2 decimal places (e.g., 32.16).) Present value $ Requirement 2: Can you afford the new system?
What is the annual cost now : Using a week (7 days) as a base period, round the orders to nearest power of 2. If you charge the fixed trucking fee only once for deliveries that coincide what is the annual cost now?
Draw in third angle projection : Draw in Third Angle Projection. the following orthogonal views - a Sectional Side View from 8 on a vertical cutting plane through the centre line of the bearing journals
What will be its speed at the bottom : A box slides down a rough, 25 Degree incline with a coefficient of kinetic friction between the box and incline of 0.7. What will be its speed at the bottom
What is the annual cost now : Using a week (7 days) as a base period, round the orders to nearest power of 2. If you charge the fixed trucking fee only once for deliveries that coincide what is the annual cost now?
Determine parity-check digit for number to error detection : a single parity check code used in computer listings of registatration numbers found by doubling alternate digits, beginning from the right, and adding the digits modulo-10. the parity check digit is found by taking the tens complement of this sum..
Explain the concentration of the diluted naoh solution : If 42.1 mL of 1.02 M sodium hydroxide, measured using a graduated cylinder, is placed in a beaker filled with 300 mL of DI water, what is the concentration of the diluted NaOH solution

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd