Draw gate logic diagram and typical plc ladder logic diagram

Assignment Help Electrical Engineering
Reference no: EM13261321

Write the Boolean expression and draw the gate logic diagram and typical PLC ladder logic diagram for a control system wherein a fan is to run only when all of the conditions are met
-Input A is OFF
-Input B is ON or input C is ON, or both B and C are ON
-Inputs D and E are both ON
-One or more of inputs F, G, or H are ON

Reference no: EM13261321

Questions Cloud

Research - island of garbage : Explain the importance of the research question, and develop the discussion in logical and coherent way -
What debt-equity ratio is needed for the firm : Phil's Carvings, Inc. wants to have a weighted average cost of capital of 9.3 percent. The firm has an aftertax cost of debt of 5.5 percent and a cost of equity of 11.0 percent. What debt-equity ratio is needed for the firm to achieve their target..
How much must the member pay : An HMO pays only 75% of approved charges for its HMO patient members. If a member goes out of the approved network of providers and incurs a charge of $ 1,100, of which $ 650 is approved, how much must the member pay?
Determine how much power passes through the element : Assume a 20 V voltage drop occurs across an element from terminal 2 to terminal 1 and that a current of 4A enters terminal 2. (1) Based on passive network convention, state whether the element is absorbing or delivering power.
Draw gate logic diagram and typical plc ladder logic diagram : Write the Boolean expression and draw the gate logic diagram and typical PLC ladder logic diagram for a control system wherein a fan is to run only when all of the conditions are met -Input A is OFF -Input B is ON or input C is ON, or both B and C ..
What is the oscillators total mechanical energy : What is the oscillator's total mechanical energy as it passes through a position that is 0.749 of the amplitude away from the equilibrium position
Determine the de broglie wavelength of a helium atom : Recall from Section 14.3 that the average kinetic energy of an atom in a monatomic ideal gas is given by KE=(3/2)kT, Determine the de Broglie wavelength of a helium atom
What will be segment base that will map to physical address : If the segment base 002Bh with offset 0013h maps to physical address 002C3h in memory, what will be the segment base that will map to same physical address 002C3h using an offset of 0003h
Wrap up introduction with a thesis : Wrap up introduction with a thesis. One way to do this is to imagine you are attempting to convince a friend to visit a show about the artist.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Create a bit-array of 10 elements with appropriate values

Write a loop to count the number of 1's in the array. If there is an even number of 1's in the array then the OddParity variable will be set. Create a bit-array of 10 elements with appropriate values, and create variables for Sum and OddParity.

  Find sequence components vfa1-vfa2 and vfa0 at fault rate

At a point f in the system, there is an open-circuit fault on phase-a with a voltage across the open-circuit as Vfa , whereas Vfb =Vfc =0. Similar to the calculations of the short-circuit currents by making use of the sequence networks

  Derive the expression for transfer function

Derive the expression for TRANSFER FUNCTION and write the expression for magnitude and phase of H(f).

  What sampling rate should use for aliasing frequencies

use a third-order low pass filter with a -3dB frequency of 10 Hz to filter your signal. What sampling rate should you use to make sure any potentially aliasing frequencies are attenuated by at least -40 dB for a. A butterworth filter

  Determine what is the filter impulse response

design a 7-tap band-pass FIR filter with linear phase response. The lower cutoff frequency is 2,500 Hz, and upper cutoff frequency is 4000 Hz. The sampling frequency is 10,000 Hz. What is the filter impulse response

  Formulate the differential equation model for a motor

Formulate the differential equation model for a motor having inductance L and rotational inertia J, and electrical resistance Rw and frictional resistance Rf, driving a frictional load, Rl.

  Determine the mean-variance and standard deviation of x

Suppose X has a continuous uniform distribution over the interval [-1, 1]. (a) Determine the mean, variance, and standard deviation of X. (b) Determine the value for x such that P(fx

  What should the surface concentration of the boron implant

A Si sample is uniformly doped with phosphorus at 5 E 16 cm^-3. We make a p-n junction by implanting boron atoms into the surface layer. The implanted depth is 0.15 µm. What should the surface concentration of the boron implant

  What is the minimum value of t for reliable data sample

A 10-bit unipolar ADC with a reference of 5.00 F and a 44 micro seconds conversion time will be used to collect data on time constant measurement. Thus, the input will be of the form V (t) = 4(1-e^t/T) . What is the minimum value of T

  What percentage of the initial stored energy remains

An initially charged capacitance discharges through a resistance. At one time constant, what percentage of the initial voltage reamins What percentage of the initial stored energy remains

  Calculate the power factor at whic the source operates

In each of the three phases in a balanced delta- connected load is composed of a 10mF capacitor in parellel with a series-connected 470 ohm resistor and 4mH inductor combination, assume a phase voltage of 400 V at 50 Hz

  What is difference between block diagram and front panel

What does the DAQ Assistant do How is it useful over the legacy acquisition methods What does FFT stand for and what does it do to a real-time signal Sketch the output of an FFT analysis performed on a 100 Hz sinewave signal at 1 V.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd