Draw and label a flow chart of the process giving the

Assignment Help Mechanical Engineering
Reference no: EM13635509

A double effect evaporator is used in feed forward mode to produce fresh water from sea water vontaining 3.5wt% dissolved salts. Sea water enters the first effect at 300K at a rate of 5000kg/hr, and saturated steam at a pressure of 4 bars is fed into a tube bundle in the 1st effect. The steam condenses at 4 bars and the condensate is withdrawn at the saturation temperature corresponding to this pressure.

The heat given up by the steam condensing in the tubes causes water to evaporate from the brine solution at the pressure of 0.6 bar maintained in the effect. The exiting brine contains 5.5% salt. The steam generated in the 1st effect is fed to a tube bumdle and the steam generated in the second effect at a pressure of 0.2 bar constitute the fresh water produced in the process.

a) draw and label a flow chart of the process, giving the temperature and specific enthalpy of each stream and tell at what rate must steam be fed to the 1st effect?

Reference no: EM13635509

Questions Cloud

Estimate how long the sun would have to shine on the earth : the lsquosolar constant which describes the amount of energy that the earth absorbs as radiation from the sun is 1340 w
What conditionns or assumptions must be considered before : dilbert decides he needs a new job. he begins working at a computer repair store fixing laptops desktop computers and
Find the variation of vapor temperature and phase interface : a liquid-vapor phase change process in microgravity conditions is carried out sufficiently slowly so that a one
A 60-cm-diameter horizontal pipe gradually narrows to 40cm : a 6.0-cm-diameter horizontal pipe gradually narrows to 4.0cm. when water flows through this pipe at a certain rate
Draw and label a flow chart of the process giving the : a double effect evaporator is used in feed forward mode to produce fresh water from sea water vontaining 3.5wt
Good machines are expected to produce no more than 1 : dilbert is in charge of evaluating a new machine that manufactures shoelaces. in particular he needs to estimate the
A mixture containing only agcl and agbr weighs 200 g it : a mixture containing only agcl and agbr weighs 2.00 g. it isquantitatively reduced to silver metal which weighs 1.30
A car travels up a hill at a constant speed of 55 kmh and : a car travels up a hill at a constant speed of 55 kmh and returns down the hill at a constant speed of 22 kmh.
The diameter of the rod is 25mm internal diameter and its : a long rod is exposed at air at 298oc. it is heated at one end. a steady state condition the temp at 2points along the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd