Draw an event tree to present all possible scenarios

Assignment Help Civil Engineering
Reference no: EM132416277

If a hazard should go through three independent barriers to be exposed, and the probability of each barrier to fail is 0.001, and the consequence of hazard exposure is 3,000 cancer-deaths, estimate the risk due to this hazard. Draw an event tree to present all possible scenarios for the situation.

Reference no: EM132416277

Questions Cloud

Determine the uniform stress developed : A compressive load of 10 MPA is applied in the Y direction. Determine the uniform stress developed in X and Z directions
Calculate the sensible portion of the humidification : Calculate the sensible portion of the humidification for steam injected into the airstream (BTU/hr). Moist air at 60ºF 20% RH enters a heater and humidifier
Calculate the outlet air temperature : Calculate the outlet air temperature if the inlet air is Twb=32ºF and 40% RH. The air is flowing at 2500 cfm and is sensibly heated at a rate of 80,000 btu/hr.
Calculate the necessary flow rate of air : Calculate the necessary flow rate of air (cfm) moving over a heat exchanger if the heater is rated at 6,000 btu /hr.
Draw an event tree to present all possible scenarios : Estimate the risk due to this hazard. Draw an event tree to present all possible scenarios for the situation.
Design steel welded connections using asd : How to design steel welded connections using ASD for concentric and eccentric loading? Kindly also explain the details for each procedure.
What is a common term for life cycle analysis : 1. What is a common term for "life cycle analysis? 2. The typical team members of in creating a building are which one of the following?
Calculate the efficiency of the joint : Calculate the efficiency of the joint, if four bolts are provided in the bolt line at a pitch of 45 mm. Assume grade of steel Fe410, kb = 0.55
Find number of bolts required : If design forces required per pitch length (i) to shear a single bolt, (ii) to crush the bolt and (iii) to tear the plate are 40kN, 60kN and 50kN respectively.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What formula and information is needed to find the maximum

What is the formula to find the Maximum pressure on a form, and what information is needed to find the maximum pressure on the form?

  Determine the pressure at the point in n per m2 gage

Near the point (x, z) =(3,2) in a flow with a zero y-component (v=0), the velocity component are described by u =3x-3z, and w = 6-4z+ x. The velocities u and w are in m/s and are in the x- and z- directions, respectively.

  How to compute the normal depth of a trapezoidal channel

A trapezoidal channel with a bottom width of 4 feet and side slopes 2:1 (H:V) and a bed slope of 1 percent conveys a discharge of 50,000 gpm. Assume n = 0.025. Compute the normal depth.

  Draw the fbds of the entire assembly

Tension in the spring connecting the two arms of the lifting tongs is 150 lb.

  Are there any situations when parallel flow option

Are there any situations when parallel flow option may be preferred instead of a counter flow heat exchanger

  Determine the discharge coefficient for the nozzle meter

An unknown fluid flows through a horizontal 35-mm-diameter pipe with a Reynolds number of 100,000 and a density of 680 kg/m3. The pressure drop across a 21-mm-diameter nozzle meter placed in the pipe is 4.2 kPa.

  What real-world considerations absent in the problem

The mayor proposes financing the museum with a lump-sum tax of $24 and then opening the museum free to the public. How many times would each person visit? Calculate the benefit each person would get from the musuem, measured as consumer surplus minus..

  Determine the velocity with a static pressure in pipe

Water with a static pressure of 1.96kN/M2 flows through an 800 mm diameter pipe. A pitot tube pressure gage in this pipe reads a pressure of 5.88 kN/M2. Determine the velocity (V)

  Find out settlement if increment loading

If two similar soil samples are used for testing the consolidation. First sample shows 1 cm settlement for increment loading from 1 kg/cm2 to 2 kg/cm2.

  Determine the required mass of block a from rest

Determine the required mass of block A so that when it is released from rest it moves the 5-kg block B a distance of .75m up along the smooth inclined plane in t=2s. Neglect the mass of the pulleys and cords.

  Why fan is kept in a return airway and why the evasee shape

A shell bursts on contact with the ground and pieces from it fly in all directions with velocities up to 49 metres per second. Show that a man 122.5 metres away is in danger for 5?2 second.

  Find length of 10 equal-sized aeration basins for treatment

Calculate the length of 10 equal-sized aeration basins for secondary treatment of a wastewater flow of 10 MGD with 20,000 lb of BOD per day for a conventional activated sludge process with a maximum loading of 40 lb BOD/ 1000 ft3*d.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd