Draw a schematic of the ideal rankine cycle and the

Assignment Help Mechanical Engineering
Reference no: EM13618968

An engineer has proposed that a simple ideal Rankine cycle that uses refrigerant-134a be used to produce work with heat from a low-temperature thermal energy reservoir. The boiler operates at 1.6 MPa, the condenser at 0.5 MPa, and the turbine inlet at 80 ºC.

(a) Draw a schematic of the ideal Rankine cycle and the corresponding T- s diagram.

(b) Determine the R-134a mass flow rate needed for this cycle to produce 750 kW of power.

(c) Determine the thermal efficiency of the cycle.

Reference no: EM13618968

Questions Cloud

The power of this test against the alternative hypothesis : an experimenter suspects that a certain die is loaded that is the chances that the die lands on different faces are not
You are planning to make monthly deposits of 440 into a : you are planning to make monthly deposits of 440 into a retirement account that pays 9 percent interest compounded
The mass flow rate of the refrigerant is 005 kgs show the : a refrigerator uses refrigerant-134a as the working fluid and operates on an ideal vapor-compression refrigeration
Tarzan swings on a 300 m long vine initially inclined at an : tarzan swings on a 30.0 m long vine initially inclined at an angle of 37.0o with the vertical.a sketch a diagram and
Draw a schematic of the ideal rankine cycle and the : an engineer has proposed that a simple ideal rankine cycle that uses refrigerant-134a be used to produce work with heat
The voltage across the inductor la only depends on the : consider two wire coil inductors la and lb. the inductor la is smaller than lb in diameter and la is placed inside of
Determine the required mass flow rate of air for a net : air is used as the working fluid in a simple ideal brayton cycle that has a pressure ratio of 10 a compressor inlet
Robin wants to purchase 1000 shares of anatop inc which is : robin wants to purchase 1000 shares of anatop inc. which is selling for 5 per share. anatop does not pay dividends
Wat is the net present value npv of the acquisition to dm : dublin medical dm a large established corporation with no growth in its real earnings is considering acquiring 100 of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A specimen of aluminum having a rectangular cross section

a specimen of aluminum having a rectangular cross section 9.7 mm times 12.4 mm0.3819 in. times 0.4882 in. is pulled in

  Explain longitudinal versus transverse vibrations in a bar

Longitudinal versus Transverse Vibrations in a bar, A 48 inch long by 2 inch diameter round steel rod (E=30e6 psi, density=0.28 lb/in3) is fixed at one end and free at the other. If the rod is struck transversely so that there is both a longitudin..

  What is the approximate magnetic field b on the axis

A solenoid 2.8 m long has a radius of 0.85 cm and 660 turns. It carries a current I of 2.5 A. What is the approximate magnetic field B on the axis of the solenoid?

  Find the mass of liquid formed if the volume under the

saturated water vapor is enclosed in a piston cylinder arrangement with a volume v initial 5 liters at a temperature

  A disk has a mass of 4kg and a radius of 90mm it is at rest

a disk has a mass of 4kg and a radius of 90mm it is at rest when it is placed in contact with the belt which moves with

  Explain the maximum flow past a circular cylinder

The maximum flow past a circular cylinder is 2 X the Up stream velocity. The max velocity occurs at the center line of the top of the cylinder.

  What is difference between corrosion and stress corrosion

What is the difference between corrosion and stress corrosion cracking of pipelines? Which of them is more dangerous and why?

  What is the elastic modulus of the material

A beam of span 600mm has a load of 1 kg and deflects by 0.55mm its width is 25.4mm and depth is 6.7mm what is the elastic modulus of the material?

  Some hypothetical metal has the simple cubic crystal

some hypothetical metal has the simple cubic crystal structure i.e. atoms positioned at each of the eight corners with

  Knowing that it strikes the water 4 s after release

a stone is thrown vertically upward from a point on a bridge located 40 m above the water. knowing that it strikes the

  A random sample of 15 parts shows mean diameter 0742 inch

1. assuming that the diameters of 1000 brass plugs taken consecutively from a machine form a normal distribution with

  A bank uses a certain form at a uniform rate of 60 pads per

a bank uses a certain form at a uniform rate of 60 pads per week during each of the 52 weeks per year it is in

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd