Draw a schematic and show the control volume you have

Assignment Help Mechanical Engineering
Reference no: EM13608776

Refrigerant 22 is used in the evaporator pipe of a commercial refrigeration unit. At steady state it flows at a rate of 0.5 kg/s through the pipe of constant diameter. It enters the pipe at -­?100C with a velocity of 5 m/s and a quality of 25%. It exits at the same temperature, but as saturated vapor. (a) Draw a schematic and show the control volume you have selected; (b) Calculate the diameter of the pipe; and (c) Calculate the velocity of the refrigerant at the exit of the pipe.

Reference no: EM13608776

Questions Cloud

Calculate the velocity of air at the entry in fts the rate : a compressor pressurizes air from 1 atm to 2.38 atm at steady state. at the entry the airs temperature is 70f whereas
Ken is estimating lost revenues of 20 percent if the : this problem comes from managerial accounting a focus on ethical decision making 5th edition jackson sawyer and
The inventory of oheto company on december 21 2013 consists : the inventory of oheto company on december 21 2013 consists of the following itemspart no. quantity cost per unit cost
Great plains transportation inc is considering acquiring : great plains transportation inc. is considering acquiring equipment at a cost of 246000. the equipment has an estimated
Draw a schematic and show the control volume you have : refrigerant 22 is used in the evaporator pipe of a commercial refrigeration unit. at steady state it flows at a rate of
An aluminum cup contains 225 g of water and a 40 g copper : an aluminum cup contains 225 g of water and a 40 g copper stirrer all at 27degc. a 420 g sample of silver at an initial
Use a 01 significance level to test the claim that the : in an analysis in investigating the usefulness of pennies the cents portion of 100 randomly selected credit card
The total cost of producing two-way radios is cx32015x03x2 : the total cost of producing two-way radios is cx32015x0.3x2 where x is the number of radios produced. if the price per
Judy herzog a recent graduate of rollings accounting : judy herzog a recent graduate of rollings accounting program evaluated the operating performance of klumpe companys six

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A petrol engine uses 204 kg of petrolh of calorific value

a petrol engine uses 204 kg of petrolh of calorific value 43 mjkg. the thermal efficiency of the engine is 20.

  Compute the lift l and drag d experienced by the aircraft

the 30 mg aircraft is climbing at the angle theta15 with a thrust t of 180 kn. at the instant shown its speed is 300

  A 40 mm diameter hole is drilled 3 m deep into the steel

a 40 mm diameter hole is drilled 3 m deep into the steel shaft. when the two torque are applied determine a the maximum

  A30 l sample of gas at 25 deg c 10 atm and is cooled to 0

a gas stream containing acetone vapor in air leaves a polymer drying process. a 3.0 l sample of gas at 25 deg. c 1.0

  In figure below a charged particle moves into a region of

in figure below a charged particle moves into a region of uniform magnetic field goes through half a circle and then

  The mean diameter of a conical friction clutch

The mean diameter of a conical friction clutch is 250mm with a width of the conical surface being 50mm. The clutch is lined with a material having a coefficient of friction of 0.25

  These are all serial input parallel latched sinking driver

these include micrel mm5450 mic5821 allegro a6276ea ucn5832a and texas instruments tpic6c595. these are all serial

  What is the gage pressure of the air inside the piston what

consider the arrangement described in problem 1. a cable attached to the 100 lbm piston exerts a 200 lb force upward on

  An insulated cylinder is initially filled with saturated

an insulated cylinder is initially filled with saturated r-134a vapor at a specified pressure. thenbsprefrigerant

  Determine the required velocity

Coal discharged from a dump truck with an initial velocity (v)= 1.8m/s at 50 degrees falls on conveyor belt B. Determine the required velocity v(B) of the belt if the relative velocity with which the coal hits the belt is to be vertical.

  Question 1 a force of 750 n acts on point a in the x

question 1 a force of 750 n acts on point a in the x direction where the cables ab ac and ad are joined as shown in

  If the vector v forms an angle theta 009 rad with the

the magnitude of the velocity vector of the car is v80 fts. if the vector v forms an angle theta 0.09 rad with the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd