Draw a ladder logic diagram to represent

Assignment Help Mechanical Engineering
Reference no: EM133004539

Assignment task is to create RS logic plc for the following questions. Please make sure each plc do not collides with the sample answers attached below the questions even the output is same. And please attach each code in the solution file as well. (basically this assignment is about paraphrasing the plc codes given)

Q1. For the following state transition diagram, as shown in figure 1, write down the state equations and represent the system in a Ladder logic diagram

442_figure.jpg

Q2. A level control is used to control the level of water in a storage tank by turning a discharge pump on or off. The modes of operation are to be programmed as follows:

OFF Position -The water pump will stop if it is running and will notstart if it is stopped.

Manual Made -The pump will start if the water in the tank is at any level except low eg below the low leveL

Automatic Mode -If the level of water in the tank reaches a high point the water pump will startso that water can be removed from the tank thus lowering the level When the water level reaches a low point the p.m p will stop.

Consider a switch for ON/OFF, another switch for MAN/AUTO, and two other switches for low level and high level

If ON/OFF=1, then ON mode, if ON/OFF=0. then OFF mode
If MAN/AUTO=1, then auto mode, if MAN/AUTO=O. then manual mode

Represent the operation with a ladder logic diagram

Q3 Find out what is wrong in the following ladder logic diagram. figure 4 Explain and correct the program.

2036_figure1.jpg

Q4 Convert the following instruction list (Siemens notation) in to a ladder logic diagram. The mnemonics are provided in the Appendix (Page 2). ANB: AND branch. ORB: OR branch

The problem with correct Siemens notations:
A (A10.1 AN 102)0 (A 103 A 10.4) = 02.1

A (A 02.1 0 103) A (A 10.1 0 102) =0 22

Q5 A motor needs to be turned off after it runs for 1 minute. There is a start and stop pushbutton for the motor. The cyclic operation can be reset with a reset pushbutton. The available timer has a time base of 100 ms. Draw a ladder logic diagram to represent the operation of this motor.

Q6. An up/down-counter is used to keep count of the cars that enter and leave a parking garage. As a car enters, the enter switch triggers the upcounter. As a car leaves, the exit switch triggers the downcounter. The Lp counter and downcounter is implemented with the same counter. When the parking lot is full an LED is energized to display the information. The parking can have 100 cars in total. Represent the above operation using a ladder logic diagram.

Reference no: EM133004539

Questions Cloud

Explain to zila : Plans to withdraw cash from her credit card even though she has her ATM card with her. As a friend, you feel her decision is not wise. Explain to Zila.
Describe the arbitrage opportunity that demonstrate effect : A four-month European call option, Describe the arbitrage opportunity that is available and demonstrate the effects of the strategy at the expiration.
What is the value of the assets : The market value of the assets of a corporation is currently $290.0 million but the owners wish to only use as collateral a value that will result in an interes
Explain the key terms relevant to using a swaption strategy : Explain the key terms relevant to using a swaption strategy for the speculator's expectation. You should provide specific details on the applicable terms
Draw a ladder logic diagram to represent : Draw a ladder logic diagram to represent the operation of this motor - Find out what is wrong in the following ladder logic diagram
Calculate the forward price and value of forward contract : Calculate the forward price and the value of the forward contract in three months, assuming that the price of the stock drops to $58
How would divide up investment : Consider you have $5000 to invest in stocks. How would you divide up your investment? Which stocks would you purchase and how much for each?
Examining stochastic processes : Assume 3 risky assets X, Y, Z where the expected returnexpected return of X is 7%, the of Y is 4% and historical/ deterministic/ observed returns of Z is 0.02%.
Which stock has a higher systematic or market risk : Suppose that in the coming year, you expect Exxon-Mobil stick to have a volatility of 42% and a beta of 0.9, and Merck's stock to have a volatility of 24% and a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd