Draw a flow chart representing the control philosophy

Assignment Help Other Engineering

Reference no: EM131474784

Task 1 - 0-5v D to A converter

In this first section you are required to build an Arduino based DA converter. The main goal is to choose the converter parameters.

You are required to:

1. Design the system that produces 0-5V analog voltage output and displays main process variables using HyperTerminal (no scrolling). SP is to be displayed in milli-volts while PV is to be displayed in per cent. Include the raw value for both variables into your output.

2. The output voltage is to be set using a potentiometer connected to the pin Ao.

3. Check the accuracy of the SP readings against your multi-meter at 4.5V. Maximum deviation allowed is ± 10mV.

4. Make sure that the unfiltered PWM output reaches 0% and 100%. Provide the appropriate oscillograms.

5. Check weather your system maintains the set point after applying a load to the output of the system equal to the resistor of the RC filter. Do this check for SP = 1V, SP = 2.5V, SP = 4V. Provide suitable comments for each case.

Task 2 - Controlling the system via a serial link

You are required to:

1. Modify your system so that you are able to control the set point via serial communication to a PC. The SP value is to be sent in milli-volts.

2. Demonstrate the system performance. No load to be applied.

Task 3 - Adding feedback

In the second section you are required to build an Arduino based voltage tracker. The ultimate task of the system is to output analogue voltage that tracks the set point voltage. Set point sampling rate is 20ms.

You are required to:

1. Draw a detailed flow chart representing the control philosophy.

2. Draw a detailed circuit diagram of your system.

3. Assemble the system and capture the oscillogram showing the system response to sweeping the set point from o to 5V and back. Follow the requirements outlined below:

a) Use a potentiometer connected to pin Ao to generate the set point for the system.

b) The feedback is to be acquired via pin A1.

c) The PWM is to be generated using pin 10.

4. Obtain an oscillogram that proves that the set point sampling rate is 20ms.

5. Check that your system maintains the set point after applying a load to the output equal to the resistor of the RC filter. Do this check for SP = 1V, SP = 2.5V, SP = 4V. Provide suitable comments for each case.

Attachment:- Assignment Files.rar

Reference no: EM131474784

Questions Cloud

Derive the characteristics of the crossbar network : Four 16-bit processors are connected to four 64K x 16 memory banks through a crossbar network. The processors can access 64K memory directly.

Decrease in productivity on equilibrium prices : Analyze the effects of a decrease in productivity on equilibrium prices (wages and interest rates) and quantities.

Determine what you want to explore and discuss : Select the topic and determine what you want to explore and discuss. Provide a detailed analysis of the problems identified in the Statement of the Problem.

What constitutes a task : Study any multiprocessor system you have access to, to answer the following: What constitutes a ‘‘task''? What is the minimum task switching time?

Draw a flow chart representing the control philosophy : In the second section you are required to build an Arduino based voltage tracker. Draw a detailed flow chart representing the control philosophy

How are drugs sorted into therapeutic groups and classes : What section of a drug's package insert describes situations in which the drug should not be used because the risks outweigh the therapeutic benefits?

Show the storage of matrix to minimize the access time : Repeat Problem, if the algorithm accesses both rows and columns of the matrix.n algorithm requires access to each row of an N x N matrix.

Economic life in the united states : Would this alter economic life in the United States? How so? What problems would it entail?

Investigate the characteristics of grid computing : Study the PCI and USB bus architectures. What support do they provide for configuring multiprocessor systems?

Reviews

len1474784

4/26/2017 4:54:25 AM

I am looking for someone can do this small project. Voltage Tracker, Not use library for Arduino. Each Task and clause separate answer and separate code and separate diagram. Must be using PWM. Following pdfs one and two. Not add components. I will attach the pdfs.

Write a Review

Required(*) Message

User Account

All Pages