Drainage facility

Assignment Help Civil Engineering
Reference no: EM13890853

Drainage facility: - Drainage facility is the normal or fake evacuation of surface and sub-surface water from a territory. Numerous rural soils need waste to enhance creation or to oversee water supplies.

Sanitary sewer lines: - A sanitary sewer (likewise called a foul sewer and a secured sewer) is an underground carriage framework particularly to transport sewage from houses and business structures through funnels.

Reference no: EM13890853

Questions Cloud

Find largest tension and largest compression load : Consider the deck to be simply supported onstringers. Floor beams then transmit the load to the bottom joints of the truss. In each case find themember subjected to the largest tension and largest compression load and suggest why you wouldchoose o..
Explain one scenario in which a projective test might used : a rationale for the use of projective or objective tests and explain why. Then explain one scenario in which a projective test might be used and one scenario in which an objective test might be used to assess personality in clinical practice and e..
A paper on globalization and alternative energy : a paper on globalization and alternative energy
Calculate the amounts and compositions of phases : Calculate the amounts and compositions of phases and constituents of steel composed of iron and 0.10% carbon just above and below the eutectoid isotherm
Drainage facility : Drainage facility: - Drainage facility is the normal or fake evacuation of surface and sub-surface water from a territory. Numerous rural soils need waste to enhance creation or to oversee water supplies
Determine the volume fraction of fibers that will required : Using the data provided, determine the volume fraction of fibers that will be required. What will be the tensile strength of this composite? Assume that the matrix stress at fiber failure is 50 MPa (7250 psi)
Estimate the amount of work that was required : The cars were loaded 6 at a time, and once all 36 cars were full, the wheel made a complete rotation at constant angular speed in about 2 min. Estimate the amount of work that was required of the machinery to rotate the passengers alone
Prepare a journal entry to close out manufacturing overhead : Calculate the overapplied or underapplied overhead for the year. Prepare a journal entry to close out the Manufacturing Overhead account into Cost of Goods Sold.
Calculate the azimuths of the remaining sides : Balance the following interior angles (angles to the right) of a five-sided closed polygon traverse using method 1 of section 10.2. if the azimuth of side AB is fixed at 122-32-16, calculate the azimuths of the remaining sides

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find width of channel when flow is in critical condition

A rectangular unfinished concrete channel with wood forms is laid on a bottom slope of 0.0064 to carry a flow of 20m^3/s of water. Determine the width of the channel when the flow is in critical condition.

  Distance from the roadway to the floor of the vehicle

You are in charge of evaluating the safety (hazard) of a low water crossing. Traffic surveys show that the "Aaverage"vehicle using the crossing is semi-rectangular in shape (10 ft long, 5 ft wide, and 4.0 ft high - not including the distance from the..

  How many grder hours will be required to accomplish the job

A motor grader will require 2 pases at 3 mph., 2 pases at 4 mph., and 2 passes at 5.5 mph. to accomplish the work How many grder hours will be required to accomplish this job if the job efficiency factor is 0.75.

  How many rapid sand filter boxes of dimensions 10 m 10 m

A streamlined, high-speed train travels at 200 km/hr. The flow over the train is similar to flow over a flat plate. Estimate the boundary layer thickness at the end of the train, which is 125 m long. The temperature is 10°C.

  Determine what is the overflow rate of each tank

two sedimentation tanks operate in parallel. The combined flow to the two tanks is .1 m^3/s. the depth of each tank is 2 m and each has a detention time of 4 h.

  Where the maximum ground level concentration would occur

a power plant burns 150,000 tonnes (1 tonne = 1,000 kg) of coal each year. The coal has 2.5% sulfur content, and the air pollution control equipment removals approximately 94% of sulfur. Assume 10% of the sulfur content ends up in the ash.

  Find difference in mercury levels inside and outside tube

A glass tube with inside diameter of 2-mm is inserted vertically into a dish of mercury at 20°C. Determine the difference in mercury levels inside and outside the tube.

  What is the conversion rate for parts per million by volume

What is the conversion rate for parts per million by volume (ppmv)conversion. How is this converted into atm, Pa, and torr?

  Gathering the data information

What additional data and information should he gather,and how should he go about gathering the data information ?

  You are going to select window type and have two

you are going to select window type and have two alternatives aluminium and wood. the window size is withhigh 1418

  What is the mixed liquor suspended solids concentration

An activated sludge system treats 1500 m3/day of raw wastewater with a BOD of 250 mg/L. The reactor volume is 375 m3. The kinetic parameters were determined to be: x = 3 day-1, Y = 0.55 kg SS/kg cells, and Ks = 150 mg/L.

  Determine the moment about the pin due to the force

1.For an SO2 emission rate of 22,000 kg/day and an exhaust gas flow rate of 5.0 million m^3/hour(after the scrubber) measured at 150 C and 1atm pressure, calculate the concentration of SO2 in the exhaust gases(ppm).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd