Does the board sit in fresh water

Assignment Help Mechanical Engineering
Reference no: EM13993983

A paddleboard is 12 ft long, 18 inches wide, 4.0 inches thick, and weighs 15 pounds. If the surfer weighs 170 pounds, how deep, in inches, does the board sit in fresh water?

Reference no: EM13993983

Questions Cloud

What minimum weight of a body placed : A sphere 1 m in diameter floats half submerged in a tank of oil( Sg = 0.80). a.) What is the upward force acting on the sphere? b.) What is the minimum weight of an anchor w/ a density of 20,000 N/m^3 that will be required to submerge the sphere comp..
The base of the tank and strikes : Water flows through a 2 cm opening in the side of a tank. If the opening is 8 m below the surface of the water,what volume of a water would escape from the tank per minute?If a stream of water escapes from another hole 2 m above the base of the tank ..
What is the self-help doctrine : What is the self-help doctrine? When is this used in criminal law
Which ones offer the subsidiary the most and least independ : Of the various methods by which a corporate subsidiary can be separated from the parent company in the public markets (IPO, carve-out, spin-off, split-off, and tracking stock), which ones offer the subsidiary the most and least independence?
Does the board sit in fresh water : A paddleboard is 12 ft long, 18 inches wide, 4.0 inches thick, and weighs 15 pounds. If the surfer weighs 170 pounds, how deep, in inches, does the board sit in fresh water?
What legal claims and defenses should be asserted : What legal claims and defenses should be asserted in a suit by Professor Smitt against Justin, Ed, and the Daily Times, and how should the claims and defenses be resolved? Discuss
Maximum height for stable equilibrium in upright position : A solid block of wood weighs 62290 N/m^3. It is in a shape of rectangular parallelepiped having a 10 cm square base.If the boat floats in fresh water with the square base horizontal, what is its maximum height for stable equilibrium in upright positi..
Fows through a constant-diameter pipe : Oil (specific gravity, 0.8)  flows through a constant-diameter pipe-(pipe diameter,  D=3 inches)  that goes through a bend of angle,  θ=45°   The flow rate in the pipe is  0.12 ft3 /s.  The pressure in the pipe atAandBis  the same, namely, 11 psi . T..
Calculate the net electric force exerted on q1 : Three point charges are located at the corners of an equilateral triangle as shown. Each leg of the triangle has a length of 1.38 meters. And the charges have values as follows. Q1 = 4.61 microcoulombs, Q2 = - 8.69 microcoulombs, and Q3 = -6.09 m..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd