Dissipates heat by free convection

Assignment Help Mechanical Engineering
Reference no: EM13719873

A thin long electric heater of width 20 cm is placed with its width oriented vertically. It dissipates heat by free convection from both sides of its surface into air at 20C. If the heater should not exceed 225C, determine the length of the heater in order to dissipate 1000 W safely

Reference no: EM13719873

Questions Cloud

What is the mass flow rate of steam through the turbine : Consider a small simple Rankine Power cycle which produces 600kW power from an electric generator with an efficiency of 95%. The steam leaves the boiler at 1250psia as superheated steam and leaves the turbine at 2 psia with a quality of 90%.
Vapor compression refrigeration cycle : A vapor compression refrigeration cycle has a theoretical COP of 4.8 and provides 120,000 btu/h of cooling (same as 10 tons of cooling). The compressor is driven by a motor with an efficiency of 92%. Estimate the theoretical kW electrical demand that..
Dam is to be built such that the estimated average flow : The dam is to be built such that the estimated average flow over its crest will be Q = 3000 m^3/s. Determine the required flow over the crest of a model built to a scale of 1/25
What is the entropy generation in the process : A thermodynamicist is attempting to model the process of balloon inflation by assuming that the elastic casing behaves like a spring opposing the expansion as presented in the figure. As air is admitted, the spring is compressed.
Dissipates heat by free convection : A thin long electric heater of width 20 cm is placed with its width oriented vertically. It dissipates heat by free convection from both sides of its surface into air at 20C. If the heater should not exceed 225C, determine the length of the heater in..
The total heat transfer rate from the plate to the air : Air at 40C flows over a 2m long flat plate with a free stream velocity of 7 m/s. Assume the width of the plate (into the paper) is 0.5m. If the plate is at constant temperature of 100C,
Air undergoes an isentropic process : Air undergoes an isentropic process from P_1 = 100 kPA and T_1 = 300 K to a final state where the temperature is 700 K. Assuming an ideal gas, find P_2 in kPa using both the ideal gas tables and assuming a constant specific heat ratio at the average ..
What could be done to limit or deny these lawsuits : In the prison system of today, inmates are overburdening the courts with lawsuits. What could be done to limit or deny these lawsuits?
Explain the development of prisons used criminal offenders : Before the development of prisons, physical punishments were commonly used on criminal offenders. Discuss if corporal punishments would again serve a purpose in dealing with some of today's offenders. Give examples

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd