Discuss what steps operator can take to reduce instability

Assignment Help Electrical Engineering
Reference no: EM13255666

The steering wheel has backlash. This means there is a delay between the time the wheel is turned, and the time the car responds. The driver tends to overturn, which leads to instability and lack of control of the car. In the presence of backlash, discuss what steps the operator can take to reduce the instability?

Reference no: EM13255666

Questions Cloud

How much force will be necessary to get to start sliding : An aluminum casting that has a mass of 10 kg sits on a steel surface. How much force will be necessary to get it to start sliding. The static coefficient of friction (mu) for aluminum on steel is 0.61.
How much force will be necessary to get to start sliding : An aluminum casting that has a mass of 10 kg sits on a steel surface. How much force will be necessary to get it to start sliding. The static coefficient of friction (mu) for aluminum on steel is 0.61.
Calculate the depreciation expense : Calculate the depreciation expense. (Do not round intermediate calculations and round your final answer to nearest whole dollar amount.)
How much force will be necessary to get to start sliding : An aluminum casting that has a mass of 10 kg sits on a steel surface. How much force will be necessary to get it to start sliding. The static coefficient of friction (mu) for aluminum on steel is 0.61.
Discuss what steps operator can take to reduce instability : The steering wheel has backlash. This means there is a delay between the time the wheel is turned, and the time the car responds. The driver tends to overturn, which leads to instability and lack of control of the car.
What is the book value of klingons total assets today : Klingon's current balance sheet shows net fixed assets of $4 million, current liabilities of $770,000, and net working capital of $245,000. If all the current assets were liquidated today, the company would receive $1.12 million cash.
Find value of capacitance needed to bring current in phase : single phase motor draws 20A from a 200V, 50Hz supply with a lagging power factor of 0.8. Calculate the value of the capacitance needed to bring the current in phase with the voltage.
What was the angular acceleration of the arm : A blower releases a ball down the lane with a linear velocity at release of 12 meters per second. what was the angular acceleration of the arm to the release point
Cell phone chargers by movement : Cell phone chargers by movement - Need to check this page. Grammar, punctuation mark, rewrite any word or sentence.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Which one will store most charge

For a circuit with resistor of 10 K ohm and a capacitor of 5 micro Farads, what is the time constant in second?

  Find the expression for the induced emf as function of time

A circular loop of radius a is located in the y-z plane center at the origin in the presence of a uniform B field pointed in the +x direction. At t=0 the loop is rotated counter clockwise with radial frequency about the z-axis.

  Calculate value of multiplier resistor to obtain full scale

An AC Voltmeter uses a bridge rectifier and 100 ohm PMMC which requires a 1mA DC current for full-scale deflection. Assuming ideal diodes, calculate the value of the multiplier resistor to obtain full scale deflection with 10 V AC applied to the i..

  What are the average and the marginal cost per unit

An assembly line can produce 90 units per hr. The line hrly cost is $4500 on stright line ( the first 8 hrs). Workers are guaranteed a minimum of 6 hrs. There is a 50% premiun for overtime (time and a half), how ever productivity drops by 5%.

  Determine the trigonometric fourier series coefficients

The exponential Fourier series coecients for a signal x(t) are: ak= { 1.57 when k=0, 0 when k is even and k doesnt equal 0, ((-1)(k-1)/2)/k when k is odd} Determine the following: (a) Plot the spectrum of the Fourier series.

  Determine the phase currents iab-ibc and ica of the load

A balacnced, three-phase, delta-connected load is supplied by a balanced, three-phase, wye-connected source over a balanced three-phase line. the source voltages are in abc phase sequence in which Van is 19.94

  Determine power and limiting error of the power

determine power and limiting error of the power?

  Determine the load torque if the rotational losses are 500 w

A dc shunt motor of 50 hp, 250 V is connected to a 230 V supply and is drawing an armature current of 200 A, and is running at speed of 1200 rpm. Its armature resistance is Ra = 0.2 ohms.

  Could it be dangerous to touch the exposed end of the wire

Sitting in front of you is a box; you cannot see iside the box. The box has a power cord that is plugged into a working wall socket. There is a wire coming out of the box; the end of the wire outside the box is exposed (not insulated) and is not c..

  Calculate the built-in voltage of a junction

Calculate the built-in voltage of a junction in which the p and n regions are doped equally with 10^16 atoms/cm3. Assume ni =.5x10^10/cm^3.  With the terminals left open, what is the width of the depletion region

  Design the simple game for the two players

Each player has 8 switches that have a value of 0 to 7 and the game has a 3-bit counter that will generate a random number between 0 and 7. The player that can come as close a possible to the random number

  Determine what is the angle of the middle one

Unpolarized light is incident on three polarizers: The first making an angle of 0 degrees with the vertical; the second making an angle of degrees with the vertical; and the last one making an angle of 90 degrees with the vertical.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd